22
VXP Series Operation Manual rev 1.0.2
11. Technical Specifications
Model
VXP 8.2
Peformance
Frequency Response (-3 dB)
1
Full range mode
75 Hz - 35 kHz
Frequency Range (-10 dB)
1
Full range mode
60 Hz - 45 kHz
Frequency Response (-3 dB)
1
Hi-Pass mode
100 Hz - 35 kHz
Frequency Range (-10 dB)
1
Hi-Pass mode
80 Hz - 45 kHz
Dispersion (-6 dB)
90 degrees conical
Driver Complement
1 x 200 mm (8.00”) constant directivity Dual Concentric™, 1 x 200 mm (8.00”) bass driver
Crossover
Passive 360 Hz and 1.5 kHz, with dynamic HF protection
Directivity Factor (Q)
8.1 averaged 1 kHz to 8 kHz
Directivity Index (DI)
9.2 dB averaged 1 kHz to 8 kHz
Rated Maximum SPL
2
117 dB (average), 123 dB (peak)
Distortion
10% Full Power (8.94 V)
2nd Harmonic 3rd Harmonic
250 Hz
0.58% 0.34%
1 kHz
0.34% 0.69%
10 kHz
1.73% 0.15%
1% Full Power (2.83 V)
2nd Harmonic 3rd Harmonic
250 Hz
0.15% 0.15%
1 kHz
0.11% 0.37%
10 kHz
0.74% 0.22%
Construction
Enclosure
19.20 litre, 15 mm (0.62”) birch plywood, vented and internally braced.
Finish
Textured black or white paint, with custom colours on request.
Powder coated perforated steel grille, Airnet cloth behind
Connectors
1 x female XLR (input), 1 male XLR (link), 1 x Neutrik Powercon
Controls & Indicators
Level Control
Power LED (Blue)
Signal LED (Red/Green)
Limit/Protect LED (Red)
Full Range / HighPass Switch (110 Hz)
Power Mode Switch
Power Switch
Fittings
4 x M10 yoke bracket inserts
2 x Integrip carrying handles
Blanking plate for optional VTH pole mount
Dimensions
590 x 280 x 275 mm (HxWxD), 23.2 x 11.0 x 10.8” (HxWxD)
Net Weight
17.5 kg (38.6 lbs)
Shipped Weight
20.0 kg (44.1 lbs)
Electronics
Maximum signal input for clip
Input attenuator at Maximum: +4.5 dBu
(Hard clip will occur at +14.5 dBu input signal)
Dynamic Range
106 dB
Amplifier efficiency
>90%
Damping Factor
>400 ref 8 ohms at 1 kHz
Distortion
<0.05% @ 1 kHz -3 dB output (22 kHz bandwidth)
Input Impedance
10 kohms unbalanced, 20 kohms balanced
Protection systems
Over Current
Output current limiter, always active
Clip limiter
Output voltage clip limiter, always active
Temperature
Over temperature causes protective mute
Brownout
Automatic protection & recovery
Mains
Inrush current limiter
Indicators
1x Power LED, 1x signal LED, 1x Limit LED
(Power LED: Red = StandBy, Green = On, Amber = Temperature protection active)
Amplifier Type
Inherently bridged, globally modulated, high performance single channel class D
PSU Specifications
Input Connector
Locking Neutrik Powercon
Voltage Selection
Universal mains input
Type
High efficiency, regulated switch mode power supply
Efficiency
>85% typical
Input voltage
100 Vac-240 Vac +/- 10%, 50-60 Hz +/-10%
Mains fuse
Internal
Fuse type
3,15AT
Other features
Inrush current limiter
StandBy power consumtion
<1 W
Idle power consumption
<15 W
Maximum power consumtion
250
W
1. Average over stated bandwidth. Measured at 1 metre on axis.
2. Unweighted pink noise input, measured at 1 metre in an anechoic chamber
A full range of measurements, performance data, and Ease™ Data can be downloaded from www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications,
which Tannoy reserves the right to alter without prior notification.
