Tanox WeldGuard ADF-206S User Manual Download | Manualshive

Page: 12 / 16

background image

11

SECTION 7 – REPLACMENT OF BATTERY

When upon pressing the TEST button no flashing of the filter is visible, the lithium battery

power is too low and needs to be replaced immediately

The ADF filter uses CR2032 3V LITHIUM BATTERY, to replace the battery release the

cartridge from the retainers and tabs as seen on section 5, slide the battery compartment

out. Replace the old battery with a new one. Make sure the positive end of the battery is

facing up. Slide the battery compartment back to its place, lock the cartridge back to its

place and press the TEST button. Make sure flashing of the filter is visible.

AUTO DARKENING FILTER

SENSITIVITY

DELAY

5-9

9-13

TEST

EN379

LITHIUM BATTERY

CR2032

3V

«
...
10
11
12
13
14
...
»

Summary of Contents for WeldGuard ADF-206S

















Reviews:

No comments

Related manuals for WeldGuard ADF-206S

Brand: Unex Pages: 24

Brand: NEC Pages: 2

Brand: Quark-Elec Pages: 2

Brand: Quark-Elec Pages: 2

Brand: Pivot Pages: 4

Brand: Whispbar Pages: 15

Brand: GATmatic Pages: 13

Brand: REV Pages: 2

651665 00 22-00-40

Brand: hepco & becker Pages: 5

Brand: Thule Pages: 4

Brand: Sable Pages: 15

Brand: RECARO Pages: 20

ORBISPHERE 31 9 Series

Brand: Hach Pages: 150

Single Sensor Set

Brand: Revbox Pages: 10

Brand: Viking Pages: 10

Pocket Dual Catchmon

Brand: Megacom Pages: 2

Brand: Datalogic Pages: 40

Brand: Ohlins Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands