W a l l M o u n t i n g - T h r e e I n d i v i d u a l H e a t e r s J o i n e d
When three Sorrento IP heaters are joined together they can be mounted in a horizontal or angled manner as the emitter is a universal burning
type.
When wall mounting three Sorrento IP heaters joined together in a horizontal manner, do not position the heater at an angle more than 80° and
less than 60° as shown in Fig. L.
When vertically mounting three Sorrento IP heaters joined together, ensure the mounting surface is angled so the heater projects downwards - see
Fig. C on Page. 3. Do not position the heater at an angle more than 45° and less than 30° to the horizontal as shown. Position the heater so the
cords are exiting the terminal box pointing down.
Always allow the heater to cool before attempting to reposition/move. Never attempt to move the
heater while it is switched on!
Observe the minimum safe distance between the heater body and inflammable surfaces and
objects when mounting.
Please refer to Table 1 for the recommended positioning of the heater with regards to minimum
distances. Do not install the heater in a corner!
Keep out of the reach of children.
1. Securely fasten the L-shaped wall brackets to the mounting surface using both of the fixing holes in
the short part of the bracket (see Fig. M for mounting hole centres). Please refer to Table 1 for
recommended positioning of the heater. Please note. wall fixings are not supplied. They should be
selected to substantially support the weight of the installation. If in doubt contact a professional for
advice!
2. The heater assembly should be mounted with the terminal boxes at the bottom of the heaters.
3. Fix the heater assembly to the brackets via the bolt threads on the middle heater. A serrated
washer should be placed on the threads first and the wall brackets should prise apart in order to fit
the threads in place.
4. Place a washer and a nut on the thread on the outside of the wall brackets – both sides.
5. Fully tighten the nut and bolts with the heater set at the desired angle.
6. Secure the supply cable so it is not resting on the body or obstructing the air-
vents.
Always isolate the heater from the mains supply when adjusting the angular
position.
C e i l i n g H a n g i n g - T h r e e I n d i v i d u a l H e a t e r s J o i n e d
When three Sorrento IP heaters are joined they can be hung from a ceiling from chains.
Always allow the heater to cool before attempting to reposition/move. Never attempt to move the heater while it is switched on!
Observe the minimum safe distance between the heater body and inflammable surfaces and objects when mounting.
Please refer to Table 1 for the recommended positioning of the heater with regards to minimum distances. Do not install the heater in a corner!
Keep out of the reach of children.
1. Please refer to Table 1 for recommended positioning of the heater. When
hanging from a ceiling four chains of equal length and gauge are required and
should be selected with fixings that are more than adequate to hold the weight of
the heater. If in doubt contact a professional for advice!
2. Fix the heater assembly to the chains via the hole in the centre of the joining
bars as shown in Fig. N. and ensure the heater faces directly down when
hanging.
3. Secure the supply cable so it is not resting on the body or obstructing the
air-vents.
Always isolate the heater from the mains supply when adjusting the position.
Fig. N
Fig. M
6
DRILLING HOLE TEMPLATE DIMENSIONS FOR
WALL MOUNTED BRACKETS - 3 × HEATERS
Fig. L
M o u n t i n g - I n d i v i d u a l U n i t (Wall Mounting or Chain Hanging)
The Sorrento IP heater can be wall mounted in a horizontal (Fig. A) or angled manner (Fig. C) or hung
from a ceiling (Fig. B) from chains (not supplied).
When wall mounting the Sorrento IP heater in a horizontal manner, do not position the heater at an angle
more than 90° and less than 30° as shown in Fig. A.
When mounting the Sorrento IP heater in an angled manner, ensure the mounting surface is angled so
the heater projects downwards - see Fig. C. Do not position the heater at an angle more than 45° and
less than 30° to the horizontal as shown. Position the heater so the cord is exiting the terminal box
pointing down.
When ceiling hanging the Sorrento IP heater, ensure the minimum distance from the ceiling is adhered to
as shown in Fig. B.
Always allow the heater to cool before attempting to reposition/move. Never attempt to move the heater
while it is switched on!
Observe the minimum safe distance between the heater body and inflammable surfaces and objects
when mounting.
Please refer to Table 1 for the recommended positioning of the heater with regards to minimum
distances. Do not install the heater in a corner!
Keep out of the reach of children.
1. When wall mounting, securely fasten the L-shaped wall brackets to the mounting surface using both of
the fixing holes in the short part of the bracket (see Fig. E on the next page for mounting hole centres).
Refer to Table 1 for recommended positioning of the heater. Please note. wall fixings are not supplied.
They should be selected to substantially support the weight of the installation. If in doubt contact a
professional for advice! When hanging from a ceiling two equal length and gauge chains are required
and should be selected with fixings that are more than adequate to hold the weight of the heater. Again,
if in doubt contact a professional for advice!
2. The heater should be mounted with the terminal box at the bottom of the heater when being wall
mounted.
3. When wall mounting, fix in the required angular position by tightening the fixing bolts on the brackets at
the rear of the heater as shown in Fig. D. The heater should face directly down when hanging. Ensure
that the serrated washer is placed between the surface of the wall bracket and the bracket on the
heater.
4. Secure the supply cable so it is not resting on the body or obstructing the air-vents.
Always isolate the heater from the mains supply when adjusting the position.
3
Fig. A
Fig. D
Fig. C
Fig. B
When the electrical connection is outside, it is recommended that a waterproof socket
is used for the connection/terminal. Otherwise, the plug should be connected to a
socket indoors.
If in any doubt, please contact a suitably qualified electrician.
1. Unscrew the terminal box cover at the back of the heater and feed the supply cable
through the compression gland ensuring the rubber seal is on the cable.
2. Use a minimum of 1.0mm
2
H05RN-F supply cable with 2 poles and earth and sleeve
with silicon glass fibre braided (250°C) Sleeving. The live and neutral wires must be
connected to the terminal block. See Fig 1.
3. The green/yellow wire should be connected to the clamp marked with the earth symbol using a suitable
wire terminal. Fit cord grip and terminal box saddle once wired.
4. Tighten the barrel nut of the compression gland so that the rubber seal grips the cable (Fig 2).
5. To prevent water ingress, ensure that the cover is secured well by hand tightening all for screws evenly.
AN
G
LE
D
M
O
U
N
TIN
G
S
U
R
FA
C
E
N
Fig. 1
Fig. 2
E
L
