background image

2

3

SAFETY INSTRUCTIONS

1.  Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this apparatus near water.
6.  Clean only with dry cloth.
7.  Do not block any ventilation openings. Install in accordance 

with the manufacturer’s instructions.

8.  Do not install near any heat sources such as radiators, heat 

registers, stoves, or other apparatus (including amplifiers) 

that produce heat.

9.  Do not defeat the safety purpose of the polarized or 

grounding-type plug. A polarized plug has two blades with 

one wider than the other. A grounding type plug has two 

blades and a third grounding prong. The wide blade or the 

third prong are provided for your safety. If the provided 

plug does not fit into your outlet, consult an electrician for 

replacement of the obsolete outlet.

10.  Protect the power cord from being walked on or pinched 

particularly at plugs, convenience receptacles, and the point 

where they exit from the apparatus.

11.  Only use attachments/accessories specified by the 

manufacturer.

12.  Use only with the cart, stand, 

tripod, bracket, or table specified 

by the manufacturer, or sold with 

the apparatus. When a cart is used, 

use caution when moving the cart/

apparatus combination to avoid injury 

from tip-over.

13.  Unplug this apparatus during lightning storms or when 

unused for long periods of time.

14.  Refer all servicing to qualified service personnel. Servicing 

is required when the apparatus has been damaged in any 

way, such as power-supply cord or plug is damaged, liquid 

has been spilled or objects have fallen into the apparatus, 

the apparatus has been exposed to rain or moisture, does 

not operate normally, or has been dropped.

15.  Exposure to extremely high noise levels may cause 

permanent hearing loss. Individuals vary considerably in 

susceptibility to noise-induced hearing loss, but nearly 

everyone will lose some hearing if exposed to sufficiently 

intense noise for a period of time. The U.S. Government’s 

Occupational Safety and Health Administration (OSHA) has 

specified the permissible noise level exposures shown in the 

following chart.

 

According to OSHA, any exposure in excess of these 

permissible limits could result in some hearing loss. To 

ensure against potentially dangerous exposure to high 

sound pressure levels, it is recommended that all persons 

exposed to equipment capable of producing high sound 

pressure levels use hearing protectors while the equipment 

is in operation. Ear plugs or protectors in the ear canals or 

over the ears must be worn when operating the equipment 

in order to prevent permanent hearing loss if exposure is in 

excess of the limits set forth here. 

•  Please note that the words “Lemon Bundt Cake” do not 

appear in this manual.

WARNING — To reduce the risk of fire or electric shock, 

do not expose this appliance to rain or moisture.

Duration Per Day   Sound Level dBA, 

Typical

  In Hours 

Slow Response 

Example

 

90 

Packed garage concert

 

92 

 

 

95 

VW Bus Peace Train

 

97

 

100 

Cranked psychedelic tunes

    1.5 

102

 

105 

High speed chase on C.H.I.P.s

 

0.5  

110

   0.25 or less 

115 

Loudest parts at a Heavy Metal concert

CAUTION    AVIS

RISK OF ELECTRIC 

SHOCK 

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED PERSONNEL

ATTENTION: POUR EVITER LES RISQUES DE CHOC

ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE. AUCUN

ENTRETIEN DE PIECES INTERIEURES PAR L'USAGER. CONFIER

L'ENTRETIEN AU PERSONNEL QUALIFIE.

AVIS: POUR EVITER LES RISQUES D'INCENDIE OU

D'ELECTROCUTION, N'EXPOSEZ PAS CET ARTICLE 

A LA PLUIE OU A L'HUMIDITE

   The lightning flash with arrowhead symbol within an equilateral 

triangle is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be 

of sufficient magnitude to constitute a risk of electric shock to persons.
   Le symbole éclair avec point de flèche à l'intérieur d'un triangle 

équilatéral est utilisé pour alerter l'utilisateur de la présence à 

l'intérieur du coffret de “voltage dangereux” non isolé d'ampleur 

suffisante pour constituer un risque d'éléctrocution.

   The exclamation point within an equilateral triangle is intended to 

alert the user of the presence of important operating and maintenance 

(servicing) instructions in the literature accompanying the appliance.
   Le point d'exclamation à l'intérieur d'un triangle équilatéral est 

employé pour alerter les utilisateurs de la présence d'instructions 

importantes pour le fonctionnement et l'entretien (service) dans le 

livret d'instruction accompagnant l'appareil.

Summary of Contents for BLEND16





























Reviews: