background image

•  Please handle the product carefully. Jolts, impacts or a fall even from a low height 

can damage the product.

•  Also observe the safety and operating instructions of any other devices which are 

connected to the product.

•  When setting up the product, make sure that the cable is not pinched, kinked or 

damaged by sharp edges.

•  Always lay the cables so that nobody can trip over or become entangled in them. 

This poses a risk of injury.

•  Never use the product immediately after it has been brought from a cold room 

into a warm one. The condensation generated could destroy the product. Allow 

the device to reach room temperature before connecting and using it. This may 

take several hours.

•  Never operate the product unattended.
• 

The housing heats up during operation. Ensure sufficient ventilation. The housing 

must not be covered!

•  Do not short-circuit the USB connectors.
•  Do not charge the product from a USB port of a computer or other products since 

the  power  provided  is  insufficient.  This  can  cause  damage  to  the  connected 

product.

•  Consult an expert when in doubt about operation, safety or connection of the 

device.

• 

Maintenance, modifications and repairs are to be performed exclusively by an 

expert or at a qualified shop.

•  If you have questions which remain unanswered by these operating instructions, 

contact our technical support service or other technical personnel.

b) Rechargeable batteries

•  The rechargeable battery is permanently built into the product and cannot be 

replaced.

•  Never damage the rechargeable battery. Damaging the casing of the rechargeable 

battery  might  cause  an  explosion  or  a  fire!  Unlike  conventional  batteries/

rechargeable batteries (e.g. AA or AAA type), the casing of the LiPo rechargeable 

battery does not consist of a thin sheet but rather a sensitive plastic film only.

•  Never short-circuit the contacts of the rechargeable battery. Do not throw the 

battery or the product into fire. There is a danger of fire and explosion!

•  Charge the rechargeable battery regularly, even if you do are not using the 

product. Due to the rechargeable battery technology being used, you do not need 

to discharge the rechargeable battery first.

•  Never charge the rechargeable battery of the product unattended.
•  When charging, place the product on a surface that is not heat-sensitive. It is 

normal that a certain amount of heat is generated during charging.

Operating elements

1  USB-A output
2  Battery level indicator
3  Micro USB input
4  Function button

1

3

4

2

Operation

 Check the internal battery charge level before each use.

Make sure the connection values of your mobile device match those of the product 

(see technical data).

The USB cable is not suitable for data transfer.

Remove any protective films from the product.

a) LED indicator of the battery charge level

Press the function button 

(4)

 once briefly to check the battery level. The remaining capacity on 

the battery level indicator 

(2)

 is indicated by figures on the LED display as follows:

25

Remaining capacity up to 25 %

50

Remaining capacity up to 50 %

75

Remaining capacity up to 75 %

100

Remaining capacity up to 100 %

The figure that indicates the current battery level flashes while charging.

 Operating instructions

Portable charger 
6000 LED - Model No. 1001CTF
10000 LED - Model No. 1002CTF
15000 LED - Model No. 1003CTF

Item No. and Model No. 1001CTF / 1002CTF / 1003CTF

Intended use

The product serves as a spare battery for mobile devices (for example, smartphone, tablet) 

with 5 V/DC voltage. The charger has two USB-A outputs that can be used to charge suitable 

devices. The included USB charging cable connected to the Micro USB input can be used to 

charge the internal battery. To charge the product, a USB charger (not included) is required. 

The product has a battery level indicator and is protected against overload, overcharging, and 

short circuit.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in 

bathrooms, must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use 

the product for purposes other than those described above, the product may be damaged. 

In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc. 

Read the instructions carefully and keep them. Make this product available to third parties only 

together with its operating instructions.
This product complies with the statutory national and European requirements. All company 

names and product names are trademarks of their respective owners. All rights reserved.

Delivery content

•  Portable charger
•  USB charging cable (Micro USB to USB-A)
•  Operating instructions

Latest operating instructions           

Download the latest operating instructions via the link 

www.conrad.com/downloads

 or scan the 

QR code shown. Follow the instructions on the website.

Explanation of symbols

  The lightning symbol inside a triangle is used when there is a potential risk of 

personal injury, such as electric shock.

  An exclamation mark in a triangle indicates important instructions in this operating 

manual that absolutely have to be observed.

  The arrow symbol indicates specific tips and advice on operation.

Safety instructions

Read the operating instructions carefully and especially observe the safety 

information. If you do not follow the safety instructions and information 

on proper handling in this manual, we assume no liability for any resulting 

personal injury or damage to property. Such cases will invalidate the warranty/

guarantee.

a) General

•  The device is not a toy. Keep it out of the reach of children and pets.
•  Do not leave packaging material lying around carelessly. This may become 

dangerous playing material for children.

•  Protect the product from extreme temperatures, direct sunlight, strong jolts, high 

humidity, moisture, flammable gases, vapours and solvents.

•  Do not place the product under any mechanical stress.
•  If it is no longer possible to operate the product safely, take it out of operation and 

protect it from any accidental use. Safe operation can no longer be guaranteed 

if the product:

 - is visibly damaged, 
 - is no longer working properly, 
 - has been stored for extended periods in poor ambient conditions or 
 - has been subjected to any serious transport-related stresses.

Reviews: