background image

 

 12

 

 

Rotary Tiller RXT Series

 

 

 
 

Note: Gearboxes are shipped with high performance gear grease, add indicated lubricants to specified lev-

els. It is okay to use variable viscosity gear oils.

 

Oil Level:

 

Center Gearbox:

 

Level indicated on dipstick (SAE 90)

 

Side gearbox drive:

 

Fill to oil drain plug on lower front of cover (SAE 140)

 

Right rotor bearing:

 

Grease if cap has grease nipple. Otherwise fill to side drain plug. (SAE 90 or SAE 140)

 

 

Grease:

 

 

PTO shaft cross and bearings

 

 
 
 
 
 
 
 
 

Attaching to the tractor

 

1.

 

With the Rotary Tiller on a level surface, back the Cat. 1 tractor so the tractor lift arms are even 
with the unit

lower hitch points. Be sure nothing is between the tractor and the till-

er before backing up.

 

2.

 

justable lower hitch blocks that can be slide to facilitate usage on larger tractors.

 

3.

 

Secure the lift arm in place by using a 

7/16”

 lynch pin or other fastener.

 

4.

 

Repeat with the other arm.

 

5.

 

Connect the driveline to the tractor

s PTO output shaft. Secure it in place.

 

6.

 

Connect the tractor top link to the upper hitch point of the rotary tiller.

 

7.

 

Start the tractor and slowly raise the tiller. Check for drawbar interference. Be sure that the 
PTO driveline does not bottom out when lifting the machine to it

s maximum height. If it does 

appear that it could bottom out, it is necessary to shorten the PTO driveline. (See Shortening a 
PTO Driveline section). Ensure that in the working position there is an overlap of a minimum 
of 1/3 the length of each profile.

 

 

 

Before attaching the rotary tiller to the tractor, check the unit to ensure there is oil 
in the top and side gearbox. See Maintenance section for lubricant specifications.

 

Operating Instructions 

Summary of Contents for RXT Series














































Reviews: