WARNING
For travelling at high speed, interlocking the left and right
brakes is particularly essential. Be sure not to travel at
high speed with left and right brakes being independent to
each other (not being interlocked).
7.
Do
not attempt to stop tractor using brakes, which may
cause
failure of transmission internals or prematured wear
of brake
linings.
8.
To avoid damaging brake or transmission system, be sure to
release the parking brake before travelling.
9.
While increasing the engine speed gradually, release the
clutch pedal slowly.
WARNING
1.
Release the clutch gradually. Releasing it suddenly is haz-
ardous causing the tractor to lunge.
2.
Before travelling backward, be sure to check for any obsta-
cle behind the tractor.
3.
For travelling on public road or working" at high speed, be
sure to lock the left and right brake pedals with locking plate
so
that both brakes are applied simultaneously.
4.
During high speed operation or travelling on road, do not
use differential lock.
The 4-wheel drive shift lever and PTO
shift lever should be placed in "OFF" and "NEUTRAL' posi-
tions respectively.
5.
While travelling, remove your foot off the clutch or brake
pedals.
6.
Independent use of left or right brakes should only be
a
llowed for low speed operation.
CAUTION
For travelling with 3-point linkage attached, tie it with belt
or
the like for prevention of swinging of the lower link.
7.
If any implement is mounted, turn the tractor slowly paying
particular care for the space.
8.
Do not make a sharp turn at high speed. Be sure to lower
the engine speed before turning.
9.
Before starting the operation on slope, check for the exis-
tence of stone, irregularity or other dangerous factors which
could lead to an accident.
Do not operate the tractor at steep slopes as it may cause
the vehicle to roll over.
10.While operating on downward slope, use the engine brake.
Do not place the main shift in the “NEUTRAL” position.
11.For towing, be sure to use the drawbar only. Set the hitch
point below the center line of the rear axle.
CAUTION
STOPPING THE TRACTOR
1.
By pulling throttle lever, reduce engine speed.
2.
Depress clutch pedal all the way.
3.
Keep the brake depressed until the tractor comes to a com-
plete stop.
4.
Move PTO shift lever to NEUTRAL.
5.
Move main shift lever to NEUTRAL.
6.
Remove foot off the clutch pedal slowly.
7.
Stop the engine by operating 'STOP' switch provided in the
panel.
8.
Apply parking brake.
9.
Push hydraulic control lever slowly forward to lower imple-
ment to ground.
10.Remove the key.
11.Always get off the tractor from the left side, since the right
side is the emergency exit. When you get off, do not lean on
the hand lever, mirror, mirror lever, pedals, etc., if you need
to lean on something, you can either use the handle on the
left fender or steering wheel.
CAUTION
1.
Be sure to always apply the parking brake while the tractor
is in parking or standing.
2.
Select flat and level ground for parking.
3.
Apply blocks to the front or to the back of rear wheels on the
slope.
TREAD ADJUSTMENT
FRONT:
4-wheel drive front tread is as shown below.
Thread: 31 in. (785 mm) ve 36.4 in. (925 mm.)
800 mm (31.5 in.)
940 mm (37 in.)
17
785 mm
(31.5 in.)
925 mm
(36.4 in.)
Summary of Contents for VST 818
