background image

Tarana Wireless, Inc. Proprietary and ©2021.  All rights reserved.  vG1-RN-2021-01  

G1 RN Manual — 8 

 

 

Deployment in the European Union – CE Mark 

This Product carries CE Mark: 

 

Declaration of Conformity for radio equipment under the scope of 
Directive 2014/53/EU (RED) statement 

The Radio Equipment Directive 

2014/53/EU

 (RED) establishes a regulatory 

framework for placing radio equipment on the market. It ensures a Single Market for 

radio equipment by setting essential requirements for safety and health, 
electromagnetic compatibility, and the efficient use of the radio spectrum 
Hereby, Tarana Wireless Inc. declares that the equipment documented in this 
publication is in Compliance with the essential requirements and other relevant 
provisions of Directive 2014/53/EU (RED). 
The technical documentation as required by the Conformity Assessment procedure 
is kept at Tarana Wireless Inc. location which is responsible for this product. For 

more information please contact your local Tarana Wireless Inc. Customer Service 
or Sales representative.  
This declaration is only valid for G1 systems (hardware, software, and firmware) that 

are provided for use within the EU.  If this equipment is used in a manner not 
specified by Tarana Wireless Inc. (including use of unsupported software or 

firmware), it may result in the equipment no longer being compliant with the 
regulatory requirements. 

Tarana Products described above could face some restrictions to operate 
in the following Countries: 

 

AT 

BE 

BG 

HR 

CY 

CZ 

EE 

FI 

EL 

FR 

IT 

LV 

LT 

LU 

NL 

PL 

RO 

SK 

ES 

SW 

UK 

DE 

CH 

LI 

NO 

IC 

TR 

 

 

This Product meets International guidelines for human exposure to RF 
fields 

Tarana Wireless systems are designed to be operated as to avoid contact with the 

antennas by the end user. It is recommended to install the system in a location 
where the antennas can remain at least a minimum distance as specified from the 

user in accordance to the regulatory guidelines which are designed to reduce the 
overall exposure of the user or operator.  To meet radiation exposure requirements, 
these devices should be installed at a minimum distance of 0.7083 from people or 
animals. 

E-Field Limit (V/m) 

Distance (m) 

61 

0.7083 

G1 product complies with RF Exposure Requirements: EN 62311 

Eco-Environmental Statements 

 

Electronic products and batteries bearing or referencing the symbols shown above 
shall be collected and treated at the end of their useful life, in compliance with 
applicable European Union and other local legislation. They shall not be disposed 

of as part of unsorted municipal waste. Due to materials that may be contained in 
the product and batteries, such as heavy metals, the environment and human 
health may be negatively impacted as a result of inappropriate disposal.  

WEEE, REACH and RoHS Compliance  

Tarana Wireless products have been reviewed, analyzed and found to be following 
the European Union (EU) directive for Waste Electrical and Electronic Equipment 

(WEEE) WEEE Directive 2012/19/EU, with the EU directive for the Restriction of 
Hazardous Substances (RoHS)

 

RoHS Directive 2011/65/EU and REACH Regulation 

(EC) No 1907/2006. 
WEEE Collection Programs in the U.S. and EU at end of product life (EOL), customers 
are requested to contact Tarana Wireless to plan for WEEE collection/disposal of 

their products. The Tarana collection center in the U.S. is at the following address: 
Tarana Wireless Inc. 590 Alder Drive, Milpitas, CA 95035 Telephone: 408-351-4085 
Contact: compliance@taranawireless.com

 

 

Summary of Contents for G1 RN

















Reviews: