Operation
23
Operation with tape
VIDEO Plus+ Programming
VIDEO Plus+ greatly simplifies entering the date,
channel, start and end times of a Timer Recording by
simply entering PlusCode Programming numbers.
PlusCode Programming numbers are published in most
TV guide magazines; they can vary one to nine
numbers in length.
VIDEO Plus+ and PlusCode are registered trademarks
of Gemstar Development Corporation. The VIDEO Plus+
system is manufactured under license from Gemstar
Development Corporation.
1. Make sure that TV channels have been tuned and
stored in correct
VIDEO Plus+
order.
Insert a video cassette with protection tab into your
DVD+VCR.
2. Press VIDEO Plus+.
3. Press the numbered buttons to enter the
PlusCode
of the TV programme that you wish to
record.
If you make a mistake press
F
then enter the
revised number.
4. Press OK.
If PLEASE CHECK is displayed it means that you
have entered the wrong PlusCode Programming
numbers, entered the PlusCode Programming
numbers incorrectly.
If “- -” is displayed, you have to enter the
programme number of the station, you want to
record from.
5. Press
F
or
G
to select the settings that you wish to
revise. (PR, DATE, TIME VPS and SP).
Press
D
or
E
to enter the correct information.
6. Press
G
to select the recording speed.
(
in Timer menu = VPS activated; no
in Timer
menu = VPS deactivated)
Press
D
or
E
to select the desired tape speed
(SP, IP, or LP).
IP mode determines how much tape is left and
switches speed from SP to LP, if necessary, to
complete recording the program.
IP mode is not selected when VPS is ON.
Check that the timer event details are correct.
If you wish to record from AUDIO IN and VIDEO IN
on the front or from either of the EURO SCART sock-
ets on the back of VCR, press AV to select for cor-
rect display (AV1, AV2 or AV3).
7. If you want to make another VIDEO Plus+
recording repeat stages 2 - 7.
Press i twice.
If PLEASE CHECK is displayed, you have entered
incorrect information and will need to re-enter the
data.
Press POWER to switch your DVD+VCR power off
mode.
will appear in the video recorder’s display while
your VCR waits to make the recording.
To watch a DVD during timer recording standby
mode, press POWER and DVD to switch to DVD
mode.
8. Press POWER to end recording.
Programme Delivery Control (PDC)
The Programme Delivery Control (PDC) system
adjusts the start and end times of a timer record
event. This can be particularly useful with sports
events which may run over into extra time. The PDC
signal is transmitted by the broadcaster and this
controls your video recorder’s timer. Currently only a
limited number of TV companies transmit PDC
signals. Please make sure that when recording from
channels that do not broadcast PDC that you turn
PDC OFF.
Note: Timer recordings can only be performed
if the device is in stand-by mode.
OK
i
0~9,
VIDEO PLUS+ CODE NO.
- - - - - - -
-
-
REC
OK
i
0~9,
VIDEO PLUS+ CODE NO.
24687654
3
REC
DELETE :
PR
DATE
TIME
- -
- -
SP
- -
- -
SP
- -
- -
SP
- -
- -
SP
- -
- -
SP
- -
- -
SP
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
10
PR-01
12
SP
11 11 55
~
:
:
i
PR
DATE
TIME
- -
- -
SP
- -
- -
SP
- -
- -
SP
- -
- -
SP
- -
- -
SP
- -
- -
SP
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
10
PR-01
12
SP
11 11
55
~
:
:
i
PR
DATE
TIME
- -
- -
SP
- -
- -
SP
- -
- -
SP
- -
- -
SP
- -
- -
SP
- -
- -
SP
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
- - - - - - - -
~
:
:
10
PR-01
12
SP
11 11
55
~
:
:
i
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 23
