Target DT15E, Operating Instructions And Parts List Manual

 25

and thoroughly lubricate moving parts - so the next 
job the machine is ready for operation. 

Drive belts must be tight.  When the belts are 
loose, power is lost.  Replace worn belts without 
delay! 

Replace noisy bearings immediately!  Worn 
bearings will quickly destroy the tools.  

 10. Accessories 

The following accessories and kits are available for this 
machine. See the Parts List section of this document 
for the part number. For additional information contact 
your local dealer or call our Toll free Customer Service 
Telephone number shown on the front cover: 

Weight Kit

 [ FIG. 12, FIG. 13]: 

a)  Items included in kit: 

1)  Weight Tray [Z] and Weight Tray Attaching 

Hardware [AA]. 

2)  Removable Weight Box [BB] and Safety 

Bolts [CC]. 

3)  Nine (9) Steel Weight Bars [DD] totaling 58 

Lbs. (26 kg), and Weight Bar Attaching 
Hardware [EE].  Note: Can hold an 
additional Nine (9) Weight bars (Sold 
Separately) for a Total Maximum Weight of 
117 Lbs. (53 kg). 

b)  Installation of Kit (Also See Parts List):  

1)  Remove the four (4) existing Capscrews 

installed in the weight tray mounting holes 
(used to plug the holes in the gearbox). 

2) Mount 

the 

Weight Tray [Z] using the 

Weight Tray Attaching Hardware [AA] 
supplied in the kit (Four Capscrews, 
Lockwashers, and Washers). 

3) Install 

the 

Weight Bars [DD] into the 

Weight Box [BB].  Use the Weight Bar 
Attaching Hardware [EE] to install the 
Weight Bars inside the Weight Box.  Install 
the Capscrews so that the heads are to the 
front of the weight box (outside of 
machine).  Place the smaller washers 
between the larger washers to form a 
“notch” that will hold the box assembly in 
place on the machine.  Tighten the 
Locknuts so that the Weight Bars [DD] are 
held securely in the Weight Box [BB]. 

4)  Lift the assembled Weight Box [BB] onto 

the Weight Tray [Z] (installed on the 
machine).  Align the Washers so that they 
fit into the slots in the back of the Weight 
Tray [Z].  Lower the Weight Box [BB] onto 
the Weight Tray [Z]. 

5)  Use the Hold-Down Bolts [CC] as a 

method to hold the Weight Box [BB] 

securely to the machine.  If the Hold-Down 
Bolts [CC] are not used the Weight Box 
can be lifted off of the machine, but this is 
not recommended if  the machine is to be 
used of a rough surface, or if the machine 
is to be lifted into the air for any reason. 

WARNING: DO NOT lift the machine into the 
air unless the Weight Box [BB] is securely 
fastened to the machine using the Hold-Down 
Bolts [CC].  The recommended method is to 
remove the Weight Box [BB] BEFORE lifting 
the machine.  The machine will then remain 
horizontal when lifted, using the lifting point. 

Water Tank Kit

 [FIG. 1, FIG. 11, FIG. 31]: 

a)  Items included in kit (See Diagram 4): 

1)  Water Tank Assembly [QQ1].  Includes 

Lid, Water Valve [QQ2], and Hose. 

2) Water 

Tank Bracket [QQ 3] and 

Attaching Hardware. 

3)  Nozzle Bracket Assembly (Not 

Shown), and Attaching Hardware. 

4)  Hose Clamps [QQ 4] and Attaching 

Hardware. 

b)  Installation of kit (Also See Parts List):  

1)  Water Tank Assembly [QQ1] comes 

pre-assembled.  Place Water Tank 
Assembly [QQ1] in frame as shown in 
FIG. 1.  Leave the end of the hose 
free. 

2)  Mount the Water Tank Bracket [QQ 3] 

INSIDE of the handle supports (frame) 
as shown in FIG. 1, FIG 2 and FIG. 3.  
Using two (2) each of the M8 
Capscrews, Lockwashers, Washers 
included in the kit, secure the Water 
Tank Bracket  [QQ 3] in position. 

3)  See FIG. 31.  At the back of the 

machine, to the right side of the Dust 
Port [XX] find the Hose Port Cover 
[AAA].  Using the small end of the 
Wrench (V) loosen the two (2) M8 
Capscrews that hold this cover in 
position, then rotate it counter-
clockwise until the Hose Port is 
exposed.  Re-tighten the M8 
Capscrews until the Hose Port Cover 
is secured in its lowered position. 

4)  Move the Axle into the Transport 

Position [E] [FIG. 11] and tilt the 
machine backwards until the handles 
are resting on the ground. 

5)  Under the front of the machine, and in 

front of the Accessory Disks (P), find 
and remove the two M8 Capscrews, 
Lockwashers, and Washers that match 
the pattern in the Nozzle Bracket