background image

50

TARGET FEED MASTER rev.09

7. TROUBLESHOOTING GUIDE

PROBLEM

CAUSE

SOLUTION

- The fuse of the

  PSFS-1 is blown

The valve

does not open

when the

PSFS-1 is

connected.

- Turn the power off and

replace the fuse with a 2.5A

slow blow fuse. 

Make sure not

to bend the fuse holder !

- There is a problem

with the power supply.

- Check for 12VAC at

the 12VAC terminals

of the PSFS-1.

- The wiring is incorrect

- The transformer is defective

- Check for 12 to 20VDC on

the MOTOR terminals of the

PSFS-1.

- Remove all wires from the

DIR terminal of the PSFS-1: if

the valve opens, then the 2

motor wires are inverted.

Interchange the 2 wires going

to the motor.

- The PSFS-1 is

  defective

- Replace the PSFS-1 module.

The main

controller

does not turn

on.

- Fuse F1 is blown.

- Replace the fuse.

- The wiring is incorrect. - Turn off the power.

- Remove all wires from the

  MODULE terminals of the

  main controller.

- Wait 5 minutes.

- Apply power to the main

  controller : If the controller

  starts then there is a wiring

  problem.

- Fix the wiring.

15

TARGET FEED MASTER

TARGET FEED MASTER  rev.09

Feed  Weigher  for
Breeders  VX.X

9.      Installation

9.  Installation

3.   Relay Assign.

9.3  Relay  Assign.

1.   Bin Augers
2.   Output Augers
3.   Time Clock Rlys
4.   Mixing Relay
5.   Scale 2 Valve

9.3.1  Bin  Relays
Bin  Auger  2
Mod:    3 Rly:     8
...

Module  ID  Assignment
ID#3  use  relay  1-8
ID#4  use  relay  1-16
ID#5  use  relay  17-32

9.3  Relay  Assign.

6.   ID Assignment

9.  Installation

4.   Bin Setting

9.4  Bin  Settings

1.   Bin 1
2.   Bin 2

9.4.1  Bin  1  Settings
Max fill time:   15
Re-order  point:  None
Alarm  if  empty:  Yes
Backup bin:       3

9.Installation

5.   Scale Calibr.

9.5  Scale  Calibr.

1.   Scale 1
2.   Scale 2

Scale  1
Calib  Weight:    10.0
Push + for next step
Scale is:      Empty

Feed  Weigher  for
Breeders  VX.X

10.    Password

10.  Password

Current  mode
User

10.  Password

Enter  password
00 ** **

9.2  Scale  settings

1.   Scale 1
2.   Scale 2

Scale  1
Actual  Weight:  0.00
Max Batch:   20kg
With Valve?     Yes
Blend size   50kg
Min Prox Sw.?   Yes
Alarm on Max?   Yes
Open On Alarm?   No
Use Mixer:      Yes
Mix  Time:    1:00(m:s)
Delivery:    1:00(m:s)
Stability tol:    50
Mix Each batch:  Yes
Dump  Separately:  Yes

9.  Installation

2.   Scale Settings

Summary of Contents for FeedMaster
































































Reviews: