background image

7 – Reference and specifications—Menu items

38 

TASCAM CC-222 

Owner’s Manual

Menu items

The following are the menu items that can be set 
using the 

MENU

 key. The majority of them affect 

disc recording.

Pressing the 

MENU 

key repeatedly cycles through the 

menu items. Not every menu item is available in 
every situation (for instance, if a digital input is not 
selected, the digital direct option is not shown).

Turn the 

MULTI DIAL

 to change a value.

Press the 

MULTI DIAL

 to confirm the change and exit 

the menu system.

Alternatively, keep pressing the 

MENU

 key until the 

normal time counter is displayed.

Resetting default menu values

User settings and the values of the input selection for 
1 and 2 are stored in memory, and are retained when 
the power is turned off.

To restore these settings to the factory defaults as in 
the table above, use a ballpoint pen or similar to hold 
down the 

RESET

 button on the rear panel:

While holding down the button, turn on the power to 
the unit and keep the 

RESET

 button pressed for at 

least two seconds after turning on the power. The 
menu values will be reset. The values for 

INPUT 1

 

and 

INPUT 2

 are set to LINE 1 and LINE 2 

respectively.

Tray Error!

Error in the CD tray mechanism.

Drive Error!

Error in the CD drive mechanism.

Symptom

Possible cause and remedy

Menu displayed

Meaning

Described in:

Default (factory) value

A-TRACK

Automatic track increment

“Automatic track division” on page 31

ON

S-LVL

Sound (trigger) level for track increment

“Setting the trigger level” on page 28 an
“Using the trigger level” on page 29

–54dB

COPY ID

Copy-protection on recorded discs 

“Copy-protection” on page 33

1 GEN

FADE IN

Allows fade in of recorded discs

“Fade-in and fade-out” on page 32

3s

FADE OUT

Allows fade out of recorded discs

“Fade-in and fade-out” on page 32

3s

DUB>VOL

Bypasses (THRU) or enables (ON) the 
internal volume when dubbing from tape to 
disc or disc to tape

“Dubbing tapes from the CD deck” on 
page 16 a
nd “Dubbing from tape to disc” 
on page 27

THRU

PHONO

Sends the PHONO inputs to DISC or 
TAPE

“Recording tapes from the PHONO deck” 
on page 17
 and “Recording to disc from 
the RIAA PHONO inputs” on page 27

DISC

D_DIRECT

Records directly from the digital source to 
disc

“Digital direct” on page 32

OFF

VOLUME

Digital volume control

“Signal volume” on page 24

0dB

RESET

Summary of Contents for CC-222











































Reviews: