Tascam CD-200i, Owner'S Manual

TASCAM  CD-200i

 27

4 − Playing Back CDs

•   If you press the STOP key when the empty program 

step where it is possible to add a track appears, all 
steps in the program are cleared. 

•   If you try to add more than 99 tracks, a “PGM FULL” 

error message appears. Only 99 tracks can be added.  

Checking the program 

You can check the contents of the program.

1  Press the 

PROGRAM EDIT

 key on the remote control 

while playback is stopped to put the unit into pro-

gram setting mode.

The track number and playback time of the track set as 

program step 01 is shown on the screen (playback time 

is not displayed if the loaded disc is a data CD) and 

MEMORY

 blinks.

Program step

Playback time

Track number

2  Press the 

PROGRAM EDIT

 key to show the track 

information of the next program step.

3  If you press the 

PROGRAM EDIT

 key when the final 

program step is shown, it becomes possible to add 

another program step. (No track number is dis-

played and the 

MEMORY

 indicator blinks.) 

4  Press the 

PROGRAM EDIT

 key again to exit the pro-

gram setting mode. 

Replacing a program track 

You can replace a track that has already been added to the 

program.  

1  Press the 

PROGRAM EDIT

 key on the remote control 

while playback is stopped to put the unit into pro-

gram mode.  

2  Follow the steps in “Checking the program” above 

and press the 

PROGRAM EDIT

 key to show the pro-

gram step with the track that you want to replace.  

3  Use the numeric keys or skip (

Ô

/

Â

, 

¯

/



) 

keys to select the desired track and press the 

PROGRAM EDIT

 key.  

  After replacing a track, the display shows the empty 

step at the end of the program and you can add 

another track to the end of the program if desired.

4.   Press the 

PROGRAM EDIT

 key again to exit pro-

gram setting mode. 

Adding more program tracks 

You can add tracks to the end of an already set program.  

1.  Press the 

PROGRAM EDIT

 key on the remote control 

while playback is stopped to put the unit into pro-

gram setting mode.  

2  Press the 

PROGRAM EDIT

 key until the empty 

program step where it is possible to add a track 

appears. (No track number is displayed and the 

MEMORY

 indicator blinks.)

3  Use the numeric keys or skip (

Ô

/

Â

, 

¯

/



) 

keys to select a track and press the 

PROGRAM EDIT

key.  

4  In this state, you can repeat step 3 to add more 

tracks, or you can press the 

PROGRAM EDIT

 key to 

exit program setting mode.

CAUTION

•  Although tracks can be added to the end of a 

program and tracks can be replaced with different 
tracks, tracks cannot be inserted into the middle of a 
program. 

•  If you want to insert a track into the middle of the 

program, replace and add program tracks to alter 
the program contents.

Clearing the program 

You can clear the entire program that has been set.  

1  Press the 

PROGRAM EDIT

 key on the remote control 

while playback is stopped to put this unit into pro-

gram setting mode.  

2  Press the 

PROGRAM EDIT

 key until the empty pro-

gram step appears. (No track number is displayed 

and 

MEMORY

 blinks.)

3  Press the 

STOP

 key.  “

-CLEAR-

” appears on the 

display. After the program is cleared, program set-

ting mode resumes without any tracks added to the 

program.

In addition to the above procedure, opening the disc 
tray also clears the program.