20
TASCAM CD-601MKII
PLAYBACK-RELATED FUNCTIONS
Program Playback
The program playback function can be used to play back
a disc in any desired track order. Up to 30 tracks can be
programmed.
Entering the program mode
Select the program mode using the
PLAY MODE
key.
Press the
PLAY MODE
key for the required number of times
until “
PROGRAM
” is displayed in the message display area
of the display window.
In the program mode, the disc is played backed according to
the program made by the method described as follows.
Programming
1 Press
the
MENU
key to enter the menu mode.
2 Press the +/- key, select menu No. 05 (“PROG”), and
press the
ENTER
key.
The display window changes to the program setup
screen.
3 Select the desired track using the
TRACK
key, and press
the
ENTER
key.
The selected track is set as the 1st tune (program No.
01) of the program, and the next tune (program No. 02)
can be set.
4 Repeat step 3 above for the required number of times to
make the desired program.
5 When you have finished making the program, press the
MENU
key to exit the menu mode.
Swapping programmed tracks
You can swap programmed tracks by performing the
following procedure while the program setup screen is
displayed.
1 Press the
SEARCH
key to select the program No. that
you want to swap.
2 Select the desired track using the
TRACK
key, and press
the
ENTER
key.
3 When you have finished swapping the track, press the
MENU
key to exit the menu mode.
Adding program tunes
You can add a program tune by performing the following
procedure while the program setup screen is displayed.
1 Press
the
SEARCH
key, and select the location to add a
tune.
For example, to add a new tune between the tunes
currently preset to program Nos. 2 and 3, select program
No. 3.
2 Press
the
+
key.
3 Select the track to add to using the
TRACK
key, and
press the
ENTER
key.
4 When you have finished adding tunes, press the
MENU
key to exit the menu mode.
Deleting program tunes
You can delete a program tune by performing the following
procedure while the program setup screen is displayed.
1 Press
the
SEARCH
key, and select the program number
that is preset with the tune to delete.
2 Press
the
-
key.
This deletes the tune, and the program numbers of the
following tunes are rounded up.
3 When you have finished deleting tunes, press the
MENU
key to exit the menu mode.
Clearing a program
Opening the disc tray clears the program.
[
NOTE
]
• The program settings are not cleared even if the CD
player is turned OFF with a disc loaded.
Auto Cue Function
When the auto cue function is turned ON, the CD player
automatically stands by (in the online READY or monitor
PAUSE mode) at the audio start point of the track when the
track is selected or when the auto ready function is ON. (
→
page 16 “Selecting the Track”)
Press the
AUTO CUE
key to turn the auto cue function ON/
OFF. When the auto cue function is ON, “
A.CUE
” is lit in the
display window.
z
The auto cue function ON/OFF setting is backed up on
the CD player. So, the same setting is reproduced when
the CD player is next turned ON.
After searching for the audio start point on the track with
the auto cue function ON, whether the CD player enters
the online READY mode or the monitor PAUSE mode is
determined according to the auto cue up setting described
below.
CD-601MKII_Eng.indd 20
3/26/2005 7:39:52 PM
Summary of Contents for CD-601MKII
Page 1: ...CD 601MKII CD PLAYER D00811701A OWNER S MANUAL...
Page 29: ......
