background image

38 

TASCAM CD-9010

11 – Specifications

Media and file formats

Supported media 

CD, CD-R  (CD-DA audio discs, ISO9660 Level1/Joliet/Romeo 

data discs) 

Playback file formats

WAV: 44.1/48kHz, 16/24-bit
CD-DA: 44.1kHz, 16-bit 

Number of channels

2  (stereo) 
1  (mono) 

Inputs and outputs

Analog audio inputs and outputs

MIX INPUTS (BALANCED) 

Connector: XLR-3-31 (1: GND, 2: HOT, 3: COLD) 
Input impedance: 10 kΩ
Nominal input level: +4 dBu (1.23 Vrms) 
Maximum input level: +24 dBu (12.28 Vrms) 

LINE OUTPUTS (BALANCED) 

Connector: XLR-3-32 (1: GND, 2: HOT, 3: COLD) 
Output impedance: 200 Ω
Nominal output level: +4 dBu (1.23 Vrms) 
Maximum output level: +24 dBu (12.28 Vrms) 

MONITOR OUTPUTS (UNBALANCED) 

Connector: RCA pin jack 
Output impedance: 100 Ω
Nominal output level: –10 dBv (0.32 Vrms) 
Maximum output level: +6 dBv (2 Vrms) 

PHONES

Connector: 6.3mm (1/4") standard stereo jack 
Maximum output level: 45 mW+45 mW 

 

 

 

 

(THD+N 0.1%, 32 Ω) 

Digital audio output

DIGITAL OUT (COAXIAL)

Connector: RCA pin jack 
Format: IEC60958-3 (S/PDIF consumer standard)* 
Output impedance: 75 Ω
*When the 

DIGITAL OUT TYPE

 in the 

SYSTEM

 menu is set to 

CONSUMER

DIGITAL OUT (XLR)

Connector: XLR-3-31 
Format: AES3-2003/IEC60958-4 (AES/EBU)** 
Output impedance: 110 Ω
**When the 

DIGITAL OUT TYPE

 in the 

SYSTEM

 menu is set to 

PRO

.

Control inputs and outputs 

WORD IN

Connector: BNC 
Input voltage: 5V TTL equivalent
Input impedance: 75 Ω
Permissible frequency variation during  

external synchronization: ±100 ppm
Switchable clock terminator 

WORD THRU

Connector: BNC 
Output voltage: 5V TTL equivalent
Output impedance: 75 Ω

REMOTE IN (SERIAL) 

Connector: D-sub 15-pin 

REMOTE IN (PARALLEL) 

Connector: D-sub 37-pin 
Maximum input voltage: +5.5 V 
High-level minimum input voltage: +3.75 V 
Low-level maximum input voltage: +1.25 V 
Output format: open drain (withstand voltage 50 V, 

maximum 100 mA) 
Low-level maximum output voltage: 0.5 V 
+5V power maximum supplied current: 100 mA 

Audio performance

Frequency response

20 Hz–20 kHz: ±0.5 dB 

Distortion

0.005% or less 

S/N ratio

100 dB or more 

Dynamic range

95 dB or more

Channel separation

95 dB or more

NOTE 

All audio performance ratings are for playback according to 

JEITA CP-2150 standards

Summary of Contents for CD-9010









































Reviews: