background image

4

  TASCAM CD-D1x4 

2

THIS LABEL IS ATTACHED TO THE PLACE AS ILLUSTRATED TO 
INFORM THAT THE APPARATUS CONTAINS A LASER 
COMPONENT.

2

DIESE AUFKLEBEMARKE IST AN DEM IN DER ABBILDUNG 
GEZEIGTEN ORT ANGEBRACHT UM DARAUF HINZUWEISEN, 
DASS IM INNERN DES GERATS EINE LASER-KOMPONENTE 
BEFINDET.

2

PASKRIFTEN SITTER PA APPARATEN SOM VISAS SOM 
UPPMANING OM ATT APPARATEN OMFATTAR EN INBYGGD 
LASERKOMPONENT.

2

DETTE MARKAT ER ANBRAGT SOM VIST I ILLUSTRATIONEN FOR 
AT ADVARE BRUGEREN OM AT APPARATET INDEHOLDER EN

CLASS 1 LASER PRODUCT

LASER KLASS 1

SAFETY INFORMATION

This product has been designed and manufactured according to FDA regulations "title 21, CFR, chapter 1, subchapter J, based on
the Radiation Control for Health and Safety Act of 1968", and is classified as a class 1 laser product. There is no hazardous invisi-
ble laser radiation during operation because invisible laser radiation emitted inside of this product is completely confined in the
protective housings.
The label required in this regulation is shown in 

1

.

CAUTION
- DO NOT REMOVE THE PROTECTIVE HOUSING USING A SCREWDRIVER.
- USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

- IF YOU SHOULD EXPERIENCE ANY PROBLEMS WITH THIS PRODUCT THAT CANNOT BE RESOLVED WITH THE "TROUBLE-

SHOOTING" SECTION LATER IN THIS MANUAL, CONTACT A TEAC AUTHORIZED SERVICE AGENCY.  DO NOT CONTINUE TO
USE THE PRODUCT UNTIL THE PROBLEM IS RESOLVED.

Optical pickup (MASTER): Type:

PXR-550X

Manufacturer:

MITSUMI Electric Co., Ltd.

Laser output:

Less than 0.1 mW (play) on the objective
lens

Wavelength:

777 - 787 nm

Optical pickups (slave):

Type:

SF-WO3YTC

Manufacturer:

SANYO Electric Co., Ltd.

Laser 

output:

Less than 2.0 mY (play) and 37mW
(record) on the objective lens

Wavelength:

780 – 786 nm

Summary of Contents for CD-D1X4























Reviews: