Tascam DA-302, Owner'S Manual

3

Safety Instructions

CAUTION:

≠

Read all of these Instructions.

≠

Save these Instructions for later use.

≠

Follow all Warnings and Instructions marked on the audio 
equipment.

1) Read instructions

— All the safety and operating instructions

should be read before the product is operated.

2) Retain instructions 

— The safety and operating instructions

should be retained for future reference.

3) Heed Warnings

— All warnings on the product and in the operat-

ing instructions should be adhered to.

4) Follow instructions 

— All operating and use instructions should

be followed.

5) Cleaning

— Unplug this product from the wall outlet before clean-

ing. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.

6) Attachments

— Do not use attachments not recommended by the

product manufacturer as they may cause hazards.

7) Water and Moisture

— Do not use this product near water _ for

example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.

8) Accessories

— Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall, causing serious
injury to a child or adult, and serious damage to the product. Use only
with a cart, stand, tripod, bracket, or table recommended by the manu-
facturer, or sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a mounting acces-
sory recommended by the manufacturer.

9)

A product and cart combination should be moved with care. Quick

stops, excessive force, and uneven surfaces may cause the product and
cart combination to overturn.

10) Ventilation

— Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the product  and to protect
it from overheating, and these openings must not be blocked or  covered.
The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not be placed in a
built-in installation such as a bookcase or rack unless proper ventilation
is provided or the manufacturer’s instructions have been adhered to.

11) Power Sources

— This product should be operated only from the

type of power source indicated on the marking label. If you are not sure
of the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.

12) Grounding or Polarization 

— This product may be equipped

with a polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug should still fail to fit, con-
tact your electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.

13) Power-Cord Protection

— Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, con-
venience receptacles, and the point where they exit from the product.

14) Outdoor Antenna Grounding 

— If an outside antenna or cable

system is connected to the product, be  sure the antenna or cable system
is grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper grounding of
the mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of anten-
na-discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode.

"Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention
to Section 820-40 of the NEC which provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be con-
nected to the grounding system of the building, as close to the point of
cable entry as practical.

ANTENNA
LEAD IN
WIRE

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

G

ROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)

NEC - NATIONAL ELECTRICAL CODE

ELECTRIC
SERVICE
EQUIPMENT

Example of Antenna Grounding as per
National Electrical Code, ANSI/NFPA 70

GROUND
CLAMP

15) Lightning 

— For added protection for this product during a light-

ning storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.

16) Power Lines 

— An outside antenna system should not be located

in the vicinity of overhead power lines or other electric light or power
circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them
might be fatal.

17) Overloading 

— Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in risk of fire or elec-
tric shock.

18) Object and Liquid Entry 

— Never push objects of any kind into

this product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock. Never
spill liquid of any kind on the product.

19) Servicing

— Do not attempt to service this product yourself as

opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.

20) Damage Requiring Service

— Unplug this product from the

wall outlet and refer servicing to qualified service personnel under the
following conditions:

a)

when the power-supply cord or plug is damaged.

b)

if liquid has been spilled, or objects have fallen into the product.

c)

if the product has been exposed to rain or water.

d)

if the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician
to restore the product to its normal operation.

e)

if the product has been dropped or damaged in any way.

f )

when the product exhibits a distinct change in performance _ this

indicates a need for service.

21) Replacement Parts 

— When replacement  parts are required, be

sure the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.

22) Safety Check

— Upon completion of any service or repairs to this

product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.

23) Wall or Ceiling Mounting 

— The product should be mounted to

a wall or ceiling only  as recommended by the manufacturer.

24) Heat

— The product should be situated away from heat sources

such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.