HS-4000
Release Notes
TASCAM HS-4000
5
•
When switching to on air operation mode, monitor
and headphones output might be interrupted. This has
been fixed.
•
In A/B MIXED playlist mode, if you selected multiple
entries on the entry list screen and then pressed the
CLEAR
button in the pull-up menu, the entries added
for Player B might not be removed correctly. This has
been fixed.
•
Operation stability has been improved.
V1.60 fixes
•
When loading a Project that the Session/Take Copy
function had been used with, project settings might
not be regenerated correctly. This has been fixed.
•
In playlist mode, after importing a PPL file, the pop-up
message might not disappear. This has been fixed.
•
If a new playlist was created in A/B MIXED mode, a
pop-up message asking whether to load to player A or
B would not appear and the playlist would always be
loaded to player A. This has been fixed.
•
Operation stability has been improved.
V1.53 fixes
•
In playlist mode, if an entry added before the current
entry was deleted or added again, the file might not
playback. This has been fixed.
•
When the time display mode was T/C, if an entry had its
Start Point
changed in playlist mode, this change
might not be reflected by the time counter, which
would show the unchanged start point. This has been
fixed.
•
For the 256th and later takes, skipping between marks,
as well as setting, showing and changing marks was
not possible. This has been fixed.
•
In playlist mode, the
CALL [CHASE]
button now has
no effect when the
ADJUST ENTRY
screen is open.
•
In playlist mode, during
CAPTURE BC$
execution,
transport operations might have been responded to,
preventing correct playback afterward. This is been
fixed.
•
Operation stability has been improved.
V1.52 fixes
•
The firmware has been changed so that the
BWF-
J Tally
setting on the
PARALLEL
page of the
RE-
MOTE SETUP
screen for on-air mode now maintains its
backup setting separately from other operation modes.
•
The firmware has been fixed so that when the
Fol-
low BWF-J
item on the
GENERAL
page of the
PLAY
SETUP
screen is set to ON, if a take/entry is skipped to
that has a BC$STANDBY mark set at its beginning, the
unit pauses and a BC$STANDBY tally is output.
•
The firmware has been fixed so that when
BC$STANDBY/BC$PAUSE tally output is ON, if a take/
entry is skipped, tally output is turned OFF.
•
The firmware has been fixed so that when in on-
air mode, the
ON AIR
button is ON and playback is
paused at a BC$STANDBY position, if the
ON AIR
button is turned OFF and playback is paused at a
position other than BC$STANDBY, the BC$STANDBY
tally output is turned OFF.
•
In on-air mode, when the
ON AIR
button was OFF and
playback was paused anywhere other than the first
take, if the
ON AIR
button was turned ON, playback
would not be paused at the correct position in some
cases. This has been fixed.
•
When
AUX Assign
was set to
Fader Start B
on
the
PARALLEL
page of the
REMOTE SETUP
screen,
if player B was fader started, other parallel controller
button operations would not be received. This has
been fixed.
•
If the parallel controller REC button was pressed twice
while the PLAY button was being pressed and held,
recording would start. This has been fixed.
•
In playlist mode, if an entry was assigned to a playlist
when the unit was not stopped, operation would
become impossible in some cases. This has been fixed.
•
If a USB keyboard was connected or disconnected
when the unit’s power was ON, operation would
become impossible in some cases. This has been fixed.
•
WAV and BWF files marked as read-only could not be
played back. This has been fixed.
•
The firmware has been changed so that if you try to
add or edit a mark in a WAV or BWF file that is marked
as read-only, a message now appears explaining that
this is not possible.
•
On the
SETUP
page of the
SYNC/TC
screen, when the
FrameType
setting was set to
23.976F
, if timecode
with a frame type of 29.97NDF was input, the input
frame type was shown as
30NDF
. This has been fixed to
show
29.97NDF
.
•
Operation stability has been improved.
