TASCAM MD-02/MD-02B
27
4. Press the
MULTI JOG
dial on the main unit or the
ENTER
key on the remote control.
The current disc title is shown in the character display
area, and title editing mode is activated (the cursor
blinks).
NOTE
If there is no title, nothing is shown (except for the
blinking cursor).
5. Follow the guidelines in the “Title input method”
section below to add a title, and then press the
MENU
key on the main unit or the remote control to confirm
it.
6. Eject the MD.
CAUTION
When using a disc with groups set, turn group mode
•
ON when adding titles. If you change the disc title
while group mode is OFF, the group settings could be
lost.
After setting a title, if you turn the power OFF with
•
the MD still loaded ("TOC" lit), the U–TOC will not be
recorded and the title will be lost. Ejecting the MD
disc causes the unit to write data to the U–TOC, so
always eject the disc once after adding titles.
Adding track titles
1. With playback stopped, press the
EDIT
key on the
main unit or the remote control.
2. Use the
MULTI JOG
dial on the main unit or the
+/– keys on the remote control to select “TITLE
INPUT?”
3. Press the
MULTI JOG
dial on the main unit or the
ENTER
key on the remote control.
“Title> Disc” appears on the display.
TIP
Instead of steps 1 and 2 in the above procedures, you can
press the TITLE key on the remote control. "Title> Disc"
appears on the display in the same way.
4. Use the
MULTI JOG
dial on the main unit or the
+/–
keys on the remote control to select the track that
you want to title.
For example, set “Title> 3” to select track 3.
5. Press the
MULTI JOG
dial on the main unit or the
ENTER
key on the remote control.
The current track title is shown in the character display
area, and the title editing mode is activated (the cursor
blinks).
NOTE
If there is no title, nothing is shown (except for the
blinking cursor).
6. Enter a title following the guidelines in the “Title
input method” section above, and press the
MENU
key on the main unit or the remote control to
confirm.
7. Eject the MD.
CAUTION
After setting a title, if you turn the power OFF with
the MD still loaded ("TOC" lit), the U–TOC will not be
recorded and the title will be lost. Ejecting the MD disc
causes the unit to write data to the U–TOC, so always
eject the disc once after adding titles.
Adding group titles
1. When playback is stopped, press the
EDIT
key on the
main unit or the remote control.
2. Use the
MULTI JOG
dial on the main unit or the
+/– keys on the remote control to select “TITLE
GROUP?”
3. Press the
MULTI JOG
dial on the main unit or the
ENTER
key on the remote control.
“Title Grp> ##” is shown on the display (“##” is the
group number).
4. Press the
MULTI JOG
dial on the main unit or the
ENTER
key on the remote control.
The current group title is shown in the character display
area, and title editing mode is activated (the cursor
blinks). In addition, the group number blinks in the
track number display area.
5. Enter a title following the guidelines in the “Title
input method” section above, and press the
MENU
key on the main unit or the remote control to
confirm.
CAUTION
After setting a title, if you turn the power OFF with
the MD still loaded ("TOC" lit), the U–TOC will not be
recorded and the title will be lost. Ejecting the MD disc
causes the unit to write data to the U–TOC, so always
eject the disc once after adding titles.
Dividing tracks (DIVIDE)
A track can be divided at the current position.
Track
No. 1
2
3
4
Track
No. 1
Track No.
is added
Song C
Song A Song B Song C Song D
Song E
Divide
Song A Song B
Song D
Song E
Divide Track
No. 3 into
C and D
1. Play or ready the track you want to divide.
7 − MD Editing
