20
TASCAM RC-601MKII
FUNCTIONS USING MEMO (A, B) POINTS
Confirming the Audio of Memo
Points (rehearsal)
You can confirm several times from point A or several
seconds up to point B.
In other words, you can check how any section preset
between points A and B starts and ends.
1 While disc operations are stopped or in the monitor
PAUSE mode, press the
MEMO
key to set the remote
control unit to the memo mode. (The
MEMO
indicator
lights.)
2 Press the key (
A
or
B
) of the memo point to confirm.
The indicator corresponding to the key you pressed
blinks, and the time of the memo point is displayed in the
display window.
3 Press
the
MONITOR
key.
This starts rehearsal playback, and the
MONITOR
key
blinks.
The length of the rehearsal playback time is the time (end
check time) set at menu No. 12 (end check time setting). (
→
page 26 “Checking the Ending of Tracks”)
Rehearsal operation differs according to the key (
A
or
B
)
that you pressed in step 2.
A key:
Playback starts from point A and is performed for the preset
end check time, and the remote control unit then enters the
online READY mode at point A. When rehearsal playback
ends, the
A
indicator stops blinking and lights.
B key:
Playback starts from before point B for the preset end check
time, and is performed up to point B, and then the remote
control unit enters the online READY mode at point A. When
rehearsal playback ends, the
B
indicator stops blinking and
lights.
Playing Back from Point A
When only point A is set, and monitor playback or online
playback is performed in the memo mode (while the
MEMO
indicator is lit), playback is started from point A.
In the regular playback (all tunes playback) mode, playback
is performed up to the end of the disc, and in the single
playback mode, playback is performed up to the end of the
current track.
Playing Back up to Point B
When only point B is set, and monitor playback or online
playback is performed in the memo mode (while the
MEMO
indicator is lit), playback is performed up to point B and then
stops.
[NOTE]
• When a track other than the track including point B is
played back in the single playback mode, single playback
is performed regardless of point B.
Playing between Points A and B
When both points A and B are set, and monitor playback or
online playback is performed in the memo mode (
MEMO
indicator is lit), the section between point A and B is played
back. The states after playback ends are as follows:
After monitor playback:
The remote control unit enters the online READY mode or
monitor PAUSE mode according to the auto cue up setting.
After online playback:
Disc operations stop.
Repeat Playing between Points A and B
The section between points A and B can be repeatedly
played back by combining the memo mode and the repeat
mode. (
→
page 18 “Repeat Function”)
The following operation assumes that both points A and B
are set in advance.
1 While disc operations are stopped, use the
PLAY MODE
key to set the remote control unit to the regular playback
(all tunes playback) mode.
2 Press the
REPEAT
key to turn the repeat function ON/
OFF. When the repeat function is ON, the indicator on
the
REPEAT
keytop lights, and “
REPEAT
” is displayed at
the bottom left of the display window.
3 Use the
MEMO
key to set the remote control unit to the
memo mode. (The
MEMO
indicator lights.)
4 Press the
MONITOR
key or
ON LINE
key to perform
monitor playback or online playback.
This starts repeat playback between points A and B.
[NOTE]
• Repeat playback between points A and B is not possible
in the single playback mode. When the above operation
is performed, playback returns to point A after step 4,
and the remote control unit enters the monitor PAUSE or
online READY mode.
RC-601MKII_Eng.indd 20
3/24/2005 2:38:20 PM