background image

©Copyright Task Force Tips LLC 2002-2020

1

LIX-030 September 4, 2020 Rev26

TASK FORCE TIPS LLC

MADE IN USA · tft.com 

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 · 219-462-6161 · Fax 219-464-7155

INSTRUCTIONS FOR INSTALLATION, OPERATION, AND MAINTENANCE

CROSSFIRE

®

 Monitor

with Safe-Tak™ 1250 Base

DANGER

Understand manual before use. Operation of this device without understanding the manual and

receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/

serial-number. 
This equipment is intended for use by trained and qualified emergency services personnel for

firefighting. All personnel using this equipment shall have completed a course of education

approved by the Authority Having Jurisdiction (AHJ).
This instruction manual is intended to familiarize firefighters and maintenance personnel with the

operation, servicing, and safety procedures associated with this product. This manual should be

kept available to all operating and maintenance personnel. 

FOG

STREAM

        800-348-2686

DA

NG

ER

Additional Copies A

vailable 24-hours

and Safety Instructions Befor

e Use.

Read and Understand All Operation

This Stop (pin pulled) Is Danger

ous.

Operating On P

ortable Base Below

Shown with optional PRV

See Section 

3.4

 

for Flow/Pressure 

Operating Envelope

Summary of Contents for CROSSFIRE

















Reviews: