background image

©Copyright Task Force Tips LLC  2020 

LIA-335 May 11, 2020 Rev00

MANUAL:  IN-LINE GAUGE WITH VALVE

IN-LINE PIVOTING GAUGE WITH VALVE

IN-LINE GAUGE WITH 45° VALVE

INSTRUCTIONS FOR INSTALLATION, SAFE OPERATION AND MAINTENANCE

WARNING

Understand manual before use. Operation of this device without understanding the manual and 
receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/ 
serialnumber.
This equipment is intended for use by trained and quali

fi

 ed emergency services personnel for 

fi

 re

fi

 ghting. All personnel using this equipment shall have completed a course of education 

approved by the Authority Having Jurisdiction (AHJ).
This instruction manual is intended to familiarize 

fi

 re

fi

 ghters and maintenance personnel with 

the operation, servicing, and safety procedures associated with this product. This manual 
should be kept available to all operating and maintenance personnel.

OPERATION RANGE:

PRESSURE MAX 300 PSI (20 BAR)

HYDROSTATIC PROOF TEST:

900 PSI (62 BAR) PER NFPA 1965

TASK FORCE TIPS LLC

MADE IN USA • TFT.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

Summary of Contents for IN-LINE GAUGE WITH VALVE









Reviews: