background image

MANUAL FOR SAFE OPERATION AND MAINTENANCE

Lack of foam can place operator at risk of injury or death. Establish foam flow before advancing into
hazardous situations. Make sure you do not run out of foam concentrate before the task is
complete. Check concentrate level periodically and keep an adequate supply on hand.

Improper use of foam can result in injury or damage to the environment. Follow the foam
concentrate manufacturer's instructions and fire service training to avoid the following: Using the
wrong type of foam on a fire, i.e. Class A foam on Class B flammable liquid fire; Mishandling of
concentrates; Plunging foam into pools of liquid fuels; Directing foam onto yourself or other
personnel.

There is a wide variety of foam concentrates. Each user is responsible for verifying that any foam
concentrate chosen to be used with this unit has been tested to assure that the foam obtained is
suitable for the purpose intended.

Read instruction manual before use. Operation of this device without understanding the manual
and receiving proper training is a misuse of this equipment. Users who have not read and
understood all operating and safety instructions are not qualified to operate this portable foam
system.

This manual should be kept available to all operating and maintenance personnel.

This instruction manual is intended to familiarize firefighters and maintenance personnel

with the operation, servicing, and safety procedures associated with the PRO/pak Portable Foam
System.

RATED FLOW

12 GPM at 100 PSI

45 L/MIN at 6.8 BAR

Minimum Operating Condition

7 GPM at 40 PSI

30 L/MIN at 3 BAR

Maximum Operating Condition

27 GPM at 500 PSI

100 L/MIN at 40 BAR

PRO/pak Portable

Multi-Purpose Foam System

k

a

p

/

O

R

P

k

a

p

/

O

R

P

PORTABLE MULTI PURPOSE FOAM SYSTEM

PORTABLE MULTI PURPOSE FOAM SYSTEM

PATENT PENDING — MODEL

UM12

PATENT PENDING — MODEL

UM12

DANGER

WARNING

WARNING

WARNING

©Copyright Task Force Tips, Inc. 2003-2006

LIU-030 December 7, 2006 Rev07

TASK FORCE TIPS, Inc.

2800 E. Evans Ave, Valparaiso, IN 46383-6940 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

MADE IN USA •www.tft.com

Summary of Contents for PRO/pak













Reviews: