4
21
3.3 Configuration with the mixer that controls the floor system
!
For this configuration you set <60>(
„
ModeMIXER
”
)=FLOOR
Rys.2C Controller with the 3-way mixing valve that controls the floor system
DM-
blower
TB-
safety sensor of the boiler
T1-
sensor of the boiler temperature
T2-
sensor of the WAW container
temperature
T3-
temperature sensor of the mixer system
(floor)
T4/TP-
room thermostat
T6-
sensor of the flue gas temperature
P1-
CH circulating pump
P2-
pump loading the WAW container
P3-
pump of the mixer
M-
drive of the mixer
4
5
The blower
The CH pump
The controller automatically controls the efficiency of the blower. The applied PID algorithm
enables the operation with modulation of boiler power- the level of generated heat is adjusted to what
is needed-thanks to that the combustion process is uniform (there aren
’
t any sudden changes of
temperature in the combustion chamber and chimney), is more efficient and it guarantees longer life
of the heating system. By analyzing the tendency of temperature changes the controller modifies its
settings gradually coming up to the balance point.
In case if the boiler temperature is higher than the preset one, the controller turns off the blower and
realizes scavenges. The scavenge parameter is defined by
“
”
and
“
”
and
“
”
.
If boiler temperature exceeds 42 C (
”
”
), the CH pump turns on. Below that
temperature the pumps turns off causing a faster heating of the water jacket over the dew point and in
fact extending the life of the boiler.
While loading the WAW container or if the room thermostat operates the CH pump can cyclically run
(restricting the heat flowing in to the CH system). The cyclical operation is based on switching on the
pump for 45secs and then stopping it for 4min (
”
”
).
4 C.
<34> TimeSCAVENGE
<33>
BreakSCAVENGE
<35> EfficiencySCAVENGE
<41>T.onPumpCH
<44> TimeStopPumpCH
o
o
!
!
The controller protects the system from freezing, automatically switches on the circulating pump if
the measured temperature is below
The controller realizes an after-season rundown of the pump. The pump turns on for a minute if it
doesn
’
t run for a week.
Connection cable of the controller may be replaced
only by producer or his authorized service locations
WARRANTY
WARNING !
ANY MODIFICATION OF THE CONTROLLER MADE BY USER CAN BE
THE CAUSE OF SAFETY CONDITIONS DETERIORATION AND CAN
EXPOSE THE USER TO ELECTRIC SHOCK OR DAMAGE DEVICES
SUPPLIED
.
Date of sale
Seller's signature and stamp
Zak
ł
ad elektroniczny TATAREK Jerzy Tatarek
50-559 Wroclaw, 75 Swieradowska st
ph. (071) 367-21-67, 373-14-88, fax 373-14-58; tax index number 899-020-21-48;
Bank account : BZ WBK S.A. O/WROC
Ł
AW 6910901522-0000-0000-5201-9335
www.tatarek.com.pl.; E-mail: tatarek@tatarek.com.pl
1.Warranty is valid [24] months from the date of sale.
2.Producer does not take responsibility for any mechanical damages made by user.
3.MAKING REPAIRS OR MODYFYING THE CONTROLLER BY USER IS
FORBIDDEN AND CAUSES WARRANTY CANCELATION
4.Warranty card is valid only with date of sale, seller's signature and stamp
5.Warranty and after-warranty repairs should be done only by producer, damaged
controllers should be sent to producer in order to make all repairs needed.
6.Warranty protection involves the EU
7.Warranty does not exclude, not restrict and not suspend buyer
’
s rights coming from
the incompatibility of the article with the agreement (Laws Journal No. 141 Pos. 1176)
WARNING!
1. Producer does not take the responsibility for damage
caused by atmospheric discharge
2. and overvoltage in the mains
3. Burnt fuses are not subject to warranty replacement
Register No.. GIOS: E 0002240WZ
Worn out electronic
and electric devices must be transfered to
the utilization collection place, where will
be accepted for free
ARGO-FILM
Recycling Plant No. 6
180 Krakowska st., 52-015 Wroclaw
ph.: 071 794 43 01,
0 515 122 142
