AFTER SALES SUPPORT
1300 922 271
service.australia@einhell.com
MODEL NUMBER: BT-RH1500, 08/11
8
(C) on the rotary switch (3) whilst at the same time
turning the rotary switch (3) into position B (see Fig. 9).
Important.
Please note that it is not possible to operate the hammer drill
with the hammer stop and rotation stop facilities both active
at the same time.
Important.
Only low pressure is required for hammer drilling. Excessive
pressure will exert an unnecessary force on the motor. Check
the drill bits at regular intervals. Sharpen or replace blunt drill
bits.
7. Replacing the power cable
If the power cable for this equipment is damaged, it must
be replaced by the manufacturer or its aftersales service or
similarly trained personnel to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the motor housing
free of dirt and dust as far as possible.
•
Wipe the equipment with a clean cloth or blow it with
compressed air at low pressure.
•
We recommend that you clean the device immediately
each time you have finished using it.
•
Clean the equipment regularly with a moist cloth and
some soft soap. Do not use cleaning agents or solvents;
these could attack the plastic parts of the equipment.
Ensure that no water can seep into the device.
8.2 Carbon brushes
In case of excessive sparking, have the carbon brushes
checked only by a qualified electrician.
Important!
The carbon
brushes should not be replaced by anyone but a qualified
electrician.
8.3 Maintenance
There are no parts inside the equipment which require ad-
ditional maintenance.
8.4 Ordering spare parts
Please quote the following data when ordering replacement
parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
TAURUS® is a trademark of ALDI Stores
ALDI Guarantee
Specially made for ALDI Stores to our stringent quality
specifications. If you are not entirely satisfied with this product,
please return it to your nearest ALDI store within 60 days from
the date of purchase for a full refund or replacement, or take
advantage of our after sales support by calling the supplier’s
Customer Service Hotline.
ALDI STORES
1 SARGENTS ROAD
MINCHINBURY NSW 2770
AUSTRALIA
www.aldi.com.au
08/2011
Art.Nr: 42.584.81_11011
5.1 Additional handle (Fig. 2 – Item 6)
For safety reasons you must only use the hammer drill with
the additional handle.
The additional handle (6) enables you to achieve better
stability whilst using the hammer drill. The machine must not
be used without the additional handle (6) for safety reasons.
The additional handle (6) is secured to the hammer drill by a
clamp. Turning the handle anti-clockwise (looking from the
handle) will release the clamp. Turning the handle clockwise
will tighten the clamp. First release the additional handle
clamp. You can then swing the additional handle (6) into the
most comfortable working position for you. Now turn the
additional handle in the opposite direction again until the
additional handle is secure.
5.2 Depth stop (Fig. 3 – Item 7)
The depth stop (7) is held in place with the locking screw (a)
on the additional handle (6) by means of a clamp.
•
Undo the locking screw (a) and fit the depth stop (7).
•
Set the depth stop (7) to the same level as the drill bit.
•
Pull the depth stop (7) back by the required drilling
depth.
•
Retighten the locking screw (a).
•
Now drill the hole until the depth stop (7) touches the
workpiece.
5.3. Tool insertion (Fig. 4)
•
Clean the tool before insertion and apply a thin coating
of drill bit grease to the shaft of the tool.
•
Pull back and hold the locking sleeve (2).
•
Insert the dust-free tool into the tool mounting as far
as it will go whilst turning it. The tool will lock itself.
•
Check that it is properly secure by pulling the tool.
5.4 Tool removal (Fig. 5)
Pull back and hold the locking sleeve (2) and remove the
tool.
5.5 Dust collection device (Fig. 6)
Slide the dust collection device (a) over the drill bit before
carrying out any hammer drilling vertically above your head.
6. Starting up
Important. To prevent all danger, the machine must only be
held using the two handles (6/8).
Otherwise there may be a risk of suffering an electric shock
if you drill into cables.
6.1 Switching on and off (Fig. 1)
To switch on: Press the control switch (4).
To switch off: Release the control switch (4).
6.2 Hammer stop facility (Fig. 7)
The hammer drill has a hammer stop facility for
gentle initial drilling.
•
Turn the rotary switch for the hammer stop facility (5)
to position (B) to switch off the hammer facility.
•
To switch on the hammer facility again the rotary
switch for the hammer stop facility (5) must be turned
back to position (A).
6.3 Rotation stop facility (Fig. 8 / 9)
The rotation function of the hammer drill can be
switched off for chiseling jobs.
•
To do this, press the button (C) on the rotary switch
(3) whilst at the same time turning the rotary switch
(3) into position A (see Fig. 8).
•
To switch on the rotation facility again, press button
