FRONT PANEL
OPIS EQUALIZERA PARAMETRYCZNEGO
REAR PANEL
− 3 −
3
2
− 4 −
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[12]
[13]
[14]
bass instrument INPUT
assive bass instrument INPUT
.
BASS control with MLO−system.
CONTROL with MLO−system.
MUTE on/off switch.
.
.
[JACK 6.3mm].
[JACK 6.3mm].
− Active
− P
− GAIN control − True/Boost “True” position (MIN) means that
the instrument signal is not increased at input stage.
The signal is the same as the pickup and preamp output.
−
− Triple BASS − switch to reduce or boost low frequency
[DBS−cut/OFF/DBS−boost].
− MIDDLE control.
− PUNCH triple switch − High−Punch/off/Low=Punch
− TREBLE
− Triple TREBLE − switch to reduce or boost high frequency
[CUT/OFF/PRESENCE].
− VOLUME control.
− ON/MUTE indicator
− Power amplifier CLIP indicator
− STANDBY and PROTECTION indicator
LED is illuminated when nothing is connected at the Amp
Input. If LED is illuminated when instrument is connected, the
Power Amp protection circuits are active.
[11] −
[1]
[2]
[3]
[4]
[5]
[6]
[XLR]
[combo SPEAKON and 6,3mm
− Balanced LINE OUTPUT
− SPEAKERS output
− LINE OUTPUT PRE/POST EQ switch.
− LINE OUTPUT GROUND LIFT switch.
− POWER switch.
−
.
.
EC POWER INPUT socket with AC fuse.
JACK]
4ohm − minimum impedance
It's recommended to connect 4 ohm cabinets with Speakon−
Speakon cable. This link warrants better connection quality
and reliability then Jack−Jack cable.
Fuse: 3,15A/230V
Fuse: 5,0A/120V
PRE
GND
LIFT
POST
450W/4ohm
300W/8ohm
4−8ohm
Made in Poland
D.I.
POWER
Fuse: 3.15A−230V 6.3A−120V
1
2
3 4
5
6
1
2
3 4
5
6
D
B
S
P
U
N
C
H
T
R
E
B
L
E
M
U
T
E
M
U
T
E
C
L
IP
P
R
O
T
GAIN
BASS
MIDDLE
VOLUME
TREBLE
PRE-CUBE
TEST
5
4
3
2
1
6
7
8
5
4
3
2
1
6
7
8
1
1
2
3
4
2
3
4
1
1
2
3
4
2
3
4
1
1
2
3
4
2
3
4
300
Qube
Bass Amplifier
A
B
Standby
Punch
Punch
True
Boost
BASS
GAIN
TREBLE
MIDDLE
VOLUME
PROT
ON
CLIP
SYSTEM
A
c
tiv
e
P
a
s
si
ve
MUTE
1
2
3
4
6
8
10
5
7
9
11
12
13
14
PROTECTIONS
4
This amp is armed with several Power Amp protection circuits. PROT LED
placed at front panel of the unit indicates their activity. If PROT illuminates
with constant light while instrument is connected, that means Power Amp
is blocked by PROTECT circuits. Temporary overload or short circuit at
Speaker Output will cause PA to be blocked for about 4 seconds. After this
time amp will start working again without any user action. If this kind of
situation occurs, cabinet connection and impedance should be checked
(lowest possible impedance is 4 ohms). If amp does not restart after 4
seconds, that may indicate Power Amp has overheated. It may take few
minutes before the cooling system will decrease temperature of PA to the
safe level.
4
