AFTER SALES SUPPORT
1300 922 271
service.australia@einhell.com
7
m
charged battery pack will result in overcharging
and cell damage. Do not leave batteries in the
charger for days on end.
8.
Never use or charge batteries if you suspect
that the last time they were charged was more
than 12 months previously. There is a high
probability that the battery pack has already
suffered dangerous damage (exhaustive
discharge).
9.
Charging batteries at a temperature below 10°C
will cause chemical damage to the cell and may
10. Do not use batteries which have heated during
the charging process, as the battery cells may
have suffered dangerous damage.
11.
Do not use batteries which have suffered
curvature or deformation during the charging
process or which show other non-typical
symptoms (gassing, hissing, cracking,…)
12. Never fully discharge the battery pack
(recommended depth of discharge max. 80%) A
complete discharge of the battery pack will lead
to premature ageing of the battery cells.
13. Never charge the batteries unsupervised.
1.
Wear suitable work clothes. Wear safety
goggles.
2.
Protect your cordless tool and the battery
charger from moisture and rain. Moisture and
rain can cause dangerous cell damage.
3.
Do not use the cordless tool or the battery
4.
Use the battery charger and cordless tools only
in dry conditions and an ambient temperature
of 10-40°C.
5.
Do not keep the battery charger in places where
the temperature is liable to reach over 40°C. In
particular, do not leave the battery charger in a
car that is parked in direct sunlight.
6.
Protect batteries from overheating. Overloads,
over-charging and exposure to direct sunlight
will result in overheating and cell damage.
Never charge or work with batteries which have
been overheated – replace them immediately if
possible.
7.
Storage of batteries, battery chargers and
cordless tools. Store the charger and your
cordless tool only in dry places with an
ambient temperature of 10-40°C. Store your
lithium-ion battery pack in a cool, dry place at
a temperature of 10-20°C. Protect them from
humidity and direct sunlight. Only place fully
charged batteries in storage (charged at least
40%).
8.
Prevent the lithium-ion battery pack from
freezing. Battery packs which were stored
below 0°C for more than 60 minutes must be
disposed of.
9.
When handling batteries be aware of
electrostatic charge: Electrostatic discharges
cause damage of the electronic protection
system and the battery cells. Avoid
electrostatic charging and never touch the
battery poles.
Important!
When using equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating manual with
due care. Keep this manual in a safe place, so that
the information is available at all times. If you give
the equipment to any other person, give them
these operating instructions as well.
We accept no liability for damage or accidents
which arise due to non-observance of these
instructions and the safety information.
3. Layout (Fig. 1)
1.
Torque selector
2.
Forward/Reverse switch
3.
ON/OFF switch
4.
Battery pack
5.
Pushlock button
6.
Selector switch for 1st gear to 2nd gear
7.
Keyless chuck
8.
Charging adapter
9.
Battery charger
10. Battery capacity indicator
11.
Button for battery capacity indicator
4. Proper use
The cordless drill/screwdriver is designed for
tightening and undoing screws, as well as for
drilling in wood, metal and plastic.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or
injuries of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be
voided if the machine is used in commercial, trade
or industrial businesses or for equivalent purposes.
MODEL NUMBER: BT-CD 10.8 Li,
01/13
