Service/Maintenance Guidelines
Page 16
RE-380-36 & RE-380-48
MR-380-05
REPLACEMENT PARTS
Using Non-OEM Replacement Components
To maintain peak performance, always use original Taylor-Dunn replacement parts intended for use on your vehicle.
Taylor-Dunn components are designed and tested for use on specific Taylor-Dunn model vehicles. Only use the
correct Taylor-Dunn replacement components for your Taylor-Dunn vehicle.
Electrical Components
Electrical components not tested by Taylor-Dunn (or intended for use on other Taylor-Dunn vehicles) may have
unanticipated interaction and/or interference with the vehicles control system resulting in unsafe vehicle operation
or damage to the electrical system.
Mechanical Components
Mechanical components not tested by Taylor-Dunn (or from other model Taylor-Dunn vehicles) may have an
undesirable affect on the operation of the vehicle, result in additional frame stress, or stress other components
resulting in premature failure or an unsafe condition.
Due to the unknown properties of non-Taylor-Dunn tested components or from components not originally equipped
on the vehicle, we cannot approve their use in a Taylor-Dunn vehicle.
To maintain peak performance, always use original Taylor-Dunn replacement parts intended for use on your
vehicle. Taylor-Dunn components are designed and tested for use on specific Taylor-Dunn model vehicles. Only
use the correct Taylor-Dunn replacement components for your Taylor-Dunn vehicle.
Do not modify your vehicle:
Modifications to this vehicle may have an undesirable effect on the operation of the vehicle, result in additional
frame stress, or stress other components resulting in premature failure or an unsafe condition and may lead
to an accident resulting in serious injury or death.
WARNING
When welding to the vehicle:
•
Do not weld onto any fuel tanks, electrical control components, engine,
or transmission.
• Welding shall be performed by qualified welders.
•
Disconnect the battery.
•
Disconnect all wires from other electronic modules.
•
Disconnect all wires from the engine control systems.
•
Disconnect all wires from the transmission control module.
•
Connect welding cable directly to the frame, do not connect to any
control components.
•
Welding emits showers of sparks. Protect all fuel system components,
engine intake and battery from exposure to the sparks.
Failure to follow these rules may damage electronic control modules
resulting in unsafe operation of the vehicle or result in fire causing severe
bodily injury and/or property damage.
WARNING
Summary of Contents for RE-380-36
