INSTALLATION
(Continued)
Note:
If an additional line is required, it should only be tied to the shackle in which the factory installed line is tied. If two additional lines are
required, a single line should be used by tying the half-way point fo the line to the same shackle in which the factory installed line is tied and
then wrap the line around the housing and through the opposite shackle.
Figure 3 - D-Icer Installation
Never suspend the D-Icer by its power cord.
Hand tension only on suspension lines.
OPERATION
Plug the D-Icer into a ground fault circuit interrupter
(GFCI) protected outlet rated for at least 15 amps.
Check the flow pattern of the D-Icer. If any adjustments
are required, unplug the D-Icer and make necessary
changes. If you are using the thermostat attachment be
sure to mount it in a secure location and free from the
suspension lines.
MAINTENANCE
Your D-Icer is designed for long life with a minimum of maintenance. The following simple maintenance procedures are all that is
required for years of reliable operation.
Taylor Made Products
65 Harrison Street
Gloversville, NY 12078
A Member of The Taylor Made Group
www.taylormadeproducts.com
© 2011 Taylor Made Group, LLC.
Gloversville, NY 12078
.
Zinc Anode
The zinc anode should be checked
periodically for deterioration and replaced
if severly corroded. Please note that if you
live in a high growth area, you may want to
check the zinc on a more frequent basis.
The zinc replacements may be purchased
from your local marine distributor..
HOUSING
Your D-Icer was designed with a state of the art protective black shroud. This special feature allows you to use the D-Icer in areas of extreme
growth and debris. As a part of your maintenance routine, you should keep the propeller and shroud free from entanglements as needed.
Never attempt to repair the D-Icer or remove the shroud!
Storage
When removing the D-Icer from the water
for the season it should be cleaned and
rinsed with fresh water, and stored propel-
ler side down in a cool place. This will keep
the D-Icer seals lubricated.
Propeller
The propeller will require replacement if it
becomes damaged. To replace the propeller,
unplug the D-Icer, grasp the zinc anode or
motor shaft with pliers and turn the propeller
counter-clockwise to remove it. To install a
new propeller, simply reverse the removal
procedure.
If you have any questions,
please call the Customer
Service department toll
free at 1-800-628-5188.
ACCESSORIES
Description________________________Part Number
Float Kit (1/2 - 1 HP)
6226
Float Kit (2 HP)
6230
Dock Mounting Kit
6225
Thermostat (on @ 25 off @ 35 f)
6215
Thermostat (on @ 30 off @ 40 f)
6216
The thermostat saves energy by shutting the D-Icer off automatically when the air temperature is
above freezing and on when the air temperature is below freezing.
REPLACEMENT PARTS
Description _______Part Number
Propeller
A-24417-P
Zinc Anode
41896-p
Shackle
A-24412-P
Warranty
Thank you for purchasing a Taylor Made Products D-Icer. Our oil-free units are warranted for a period of two (2) years from the date of purchase.
Should a defect arise, DO NOT SEND THE D-ICER BACK TO THE PLACE OF PURCHASE. Please call Taylor Made Products at 1-800-628-5188
for a return authorization number.
For two (2) years from the date of purchase, Taylor Made Products will, at its discretion, repair or replace for the original consumer, free of
charge, any part or parts found upon examination to be defective in material or workmanship or both. This warranty does not include the zinc anode,
ropes, electrical cord, propeller or failure due to misuse, mishandling, or improper storage or installation. Freight on defective products is the
responsibility of the consumer (UPS is the preferred method of returning a product to us). Repaired or replacement products will be shipped back to
the consumer freight prepaid. Proof of purchase is required.
TAYLOR MAKES NO EXPRESS OR IMPLIED WARRANTIES OTHER THAN WARRANTIES SET FORTH HEREIN, INCLUD-
ING, WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR FROM
ANY COURSE OF DEALING OR TRADE USAGE.
TAYLOR SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES,
INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF OPPORTUNITY OR BUSINESS PROFITS, BUSINESS INTER-
RUPTION OR ANY OTHER LOSS EVEN IF TAYLOR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
IN NO EVENT SHALL TAYLOR BE LIABLE FOR ANY AMOUNT IN EXCESS OF THE PURCHASE PRICE PAID.
