background image

OPERATING PROCEDURES

6-5 

Model 104

Operating Procedures 

 6

5. Put the control switch into the EJECT position. 

This causes the sanitizing solution in the freezing 
cylinder to be agitated. Allow it to agitate for five 
minutes.

WARNING! 

Keep fingers out of fill and 

discharge openings. Failure to do so may result in 
personal injury or component damage.

Figure 6-20

6. Put the control switch into the off position. 

7. Hold a pail beneath the ejection port, open the draw 

arm, and drain the sanitizing solution from the 
freezing cylinder. 

8. Close the draw arm.

Figure 6-21

Priming

1. With the control switch in the off position, hold an 

empty pail beneath the ejection port and open the 
draw arm.

WARNING! 

Keep fingers out of fill and 

discharge openings. Failure to do so may result in 
personal injury or component damage.

2. Pour the desired amount of mix into the funnel. The 

mix in the freezing cylinder will force out any 
remaining sanitizing solution. 

3. When full-strength mix is flowing from the ejection 

port, close the draw arm.

Figure 6-22

4. Set the timer for the time required for the batch. Allow 

the unit to operate until the buzzer sounds and the 
refrigeration system automatically cycles off.

Figure 6-23

5. Place the control switch in the AUTO position.

13014

10141

10141a

10142

Summary of Contents for 104









































Reviews: