background image

17 - ENGLISH

7 TROUBLE-SHOOTING

7.1 ALARMS MANAGEMENT

The “OMEGA” electronic card is a powerful control logic unit which signals possible
machine troubles by means of alphanumeric messages visualised on the display; the
technician shall understand them to quickly find the reason of this trouble.

MESSAGE

DESCRIPTION

REMEDIES

EME

EMERGENCY

The door is open or the safety grid on the hopper is not

completely lowered.

An intermittent beep is released.

Make sure that the door

is closed and the safety

grid on the hopper is

lowered.

TER

MOTOR

THERMAL

CUTOUT ALARM

When a motor thermal cutout is triggered, it is followed by

the blinking of  the led TER and by the release of an

intermittent beep.

After checking the

machine, press STOP to

restore correct

functioning.

EPO

STORED DATA

ALARM

When the machine is started up, the microprocessor checks

the data stored in the EPROM  memory: if this data are not

correct EPO will appear on the display, followed by the

release of an intermittent beep.

Send for a technician.

EPI

MEMORY ALARM

If, during normal functioning, the memory is not

acknowledged, EPI will appear on the display, followed by

the release of an intermittent beep.

Send for a technician.

LI

POWER SUPPLY

ALARM

If, during normal functioning, the voltage is too low, LI  will

appear on the display, followed by the release of an

intermittent beep.

Check mains voltage

and machine power

supply.

OUT

USCITE MODULE

ALARM

If, during normal functioning, the output control module is

faulty or if it is not acknowledged, OUT  will appear on the

display, followed by the release of an intermittent beep.

Send for a technician.

TA

TA ALARM

If, during normal functioning, an anomaly of the current

transformer occurs, TA  will appear on the display, followed

by the release of an intermittent beep.

Send for a technician.

UTA

TA MICRO-

PROCESSOR

ALARM

If, during normal functioning, an anomaly of the

microprocessor controlling the consistency calibration

occurs, UTA  will appear on the display, followed by the

release of an intermittent beep.

Send for a technician.

Summary of Contents for C116























Reviews: