Taylor Horizon 8752, Operator'S Manual

 34

Models 8752, 8756, 8757

Operating Procedures

031118

Step 2

Disconnect the pressure line from the pressure switch

and place it in the pail of cleaning solution.

Step 3

Press the PUMP key. This action will cause the

cleaning solution to be pumped through the air/mix

pump and out through the pressure line. After

approximately 15 seconds, press the PUMP key to

stop operation.

Step 4

Drain and connect the free end of the pressure line to

the pressure switch.

Step 5

Place an empty pail beneath the door spout, raise the

prime plug, and press the WASH and PUMP keys.

Step 6

When a steady stream of solution is flowing from the

prime plug hole in the bottom of the freezer door, pull

down the draw handle and draw off the remaining

cleaning solution.

Step 7

Once the solution stops flowing from the door spout,

close the draw valve and press the WASH and PUMP

keys to stop operation.

Repeat Steps 1 through 7

 for the other side of the

freezer on the Models 8756 and 8757.

Step 8

Place the power switch in the OFF position before

disassembling the machine.

Disassembly

 BE SURE THE POWER SWITCH IS IN THE

“OFF” POSITION TO ELIMINATE THE CHANCE OF

MOVING PARTS. CHECK TO MAKE SURE NO

LIGHTS ARE LIT ON THE CONTROL PANEL.

Step 1

Remove the handscrews, freezer door, beater(s),

shoes, scraper blades, and drive shaft(s) from the

freezing cylinder(s) and take them to the sink for

cleaning.

Step 2

Remove the air/mix pump. Unscrew the flare line from

the mix inlet tube. Disengage the pressure line from

the pressure switch and the mix inlet tube. Pull the

retaining pin out of the pump collar and slide the collar

down. Tilt the air/mix pump away from the machine

and take the entire assembly to the sink for further

disassembly and brush cleaning.

Step 3

Remove the pressure switch cap from the mix cabinet

and the diaphragm from the cap.

Repeat Steps 2 and 3

 for the other side of the freezer

on the Models 8756 and 8757.

Step 4

Remove the front drip tray and splash shield.

Brush Cleaning

Step 1

Prepare a sink with an approved cleaning solution (ex-

amples: Stera Sheen

 or Kay

−

5

). USE WARM WA-

TER AND FOLLOW THE MANUFACTURER’S SPE-

CIFICATIONS.

If an approved cleaner other than Stera Sheen

 or

Kay

−

5

is used, dilute it according to the label

instructions. 

IMPORTANT:

  Follow the label directions.

Too STRONG of a solution can cause parts damage,

while too MILD of a solution will not provide adequate

cleaning. Make sure all brushes provided with the

freezer are available for brush cleaning.

Step 2

Remove the seal(s) from the drive shaft(s).

Step 3

From the freezer door(s) remove the gasket(s), front

bearing(s), pivot pin(s), draw handle(s), draw valve(s),

prime plug(s), and the design cap(s).

Remove all o

−

rings.

Note:  

To remove o

−

rings, use a single service towel

to grasp the o

−

ring. Apply pressure in an upward

direction until the o

−

ring pops out of its groove. With

the other hand, push the top of the o

−

ring forward. It

will roll out of the groove and can be easily removed.

If there is more than one o

−

ring to be removed, always

remove the rear o

−

ring first. This will allow the o

−

ring

to slide over the forward rings without falling into the

open grooves.

Step 4

Remove the flare line(s), suction line(s), retaining

pin(s) and mix inlet fitting(s) from the pump cylinder(s).

Remove the liquid valve body(ies) from the pump

cylinder(s).