background image

Table of Contents

Models C708 & C716

Table of Contents - Page 2

Rinsing

48

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hopper Cleaning

48

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly

49

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brush Cleaning

50

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 7

Important: Operator Checklist

51

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

During Cleaning and Sanitizing

51

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting Bacterial Count

51

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Regular Maintenance Checks

51

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Winter Storage

52

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 8

Troubleshooting Guide

53

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 9

Parts Replacement Schedule

57

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 10

Limited Warranty on Equipment

58

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 11

Limited Warranty on Parts

60

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Note: Continuing research results in steady improvements; therefore, information
in this manual is subject to change without notice.

Note: Only instructions originating from the factory or its authorized translation
representative(s) are considered to be the original set of instructions.

E

2005 Carrier Commercial Refrigeration, Inc. (Original Publication)

(Updated August, 2015)

059061-M

Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this
work may be a violation of Copyright Law of the United States of America and other countries, could result
in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result
in further civil and criminal penalties.
All rights reserved.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072

Summary of Contents for Wawa C708



































































Reviews: