A
B
C
D
E
F
INSTALLATION INSTRUCTIONS
A
B
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
ASME A112.18.1/CSA B125.1, NSF-61 AND 372
TURN OFF
TURN OFF
4
A
B
D
C
B
E
E
C
F
A
A
F
G
H
SIL
IC
ON
E
B
SI
LI
CO
NE
Your installation may require new supply
lines. (Supply lines are not included.)
NOTE:
Do not use plumber’s putty,
pipe dope, or any other type
of sealing compound on water
inlet or threads. Additional
compound is not necessary.
J
H
I
6 - WASHER
7 - ESCUTCHEON
8 - BODY
9 - WASHER
10 - AERATOR
11 - AERATOR SHELL
12 - SCREW
13 - PUTTY GUARD
14 - SCREW
15 - GASKET
16 - MOUNTING NUT
17 - POP-UP BODY
18 - LIFT ROD & KNOB
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers
Adjustable and
Pipe wrench
Plumber’s putty
Safety goggles
Torque wrench
Silicone caulk
5
6
INSTALLING POP-UP DRAIN
A)
Remove pop-up plunger (A) and flange (B). Screw locknut (C) all the way down. Push
gasket (D) down. Apply silicone to underside of flange (B).
B)
Insert body into sink (from underneath). Screw flange onto body. Pivot hole (E) must face
the back of the sink.
C)
Tighten locknut (C) and gasket but do not overtighten. Remove pivot ball retaining nut (E).
D)
Slide pivot rod (F) into the eye of the pop-up plunger (A). Hand tighten retaining nut.
E)
Slide pivot rod (F) through hole in spring clip (G), then through lever strap (H) and back
through spring clip
.
F)
Insert lift rod (I) down through faucet body and then into lever strap (H). Tighten screw (J).
Connect assembly to drain.
7
8
EXPLODED DIAGRAM FOR REFERENCE
MAINTENANCE
Your new faucet is designed for years of trouble-free performance. Keep it looking
new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh
chemicals as these will dull the finish and void your warranty.
HAND TIGHTEN THE WING NUTS
From underneath the sink, hand tighten the wing nuts. Tighten gently until snug and alternate
from side to side to seat the faucet body evenly.
Don’t over tighten
FLUSHING & AERATOR CLEANING
Remove the aerator by turning it counter-
clockwise. Remove the internal parts of the
aerator by pushing them out with your fingers.
Remove any debris. Turn on hot and cold
water supplies. Turn faucet handles all the
way on and run water through the spout
for about a minute to remove debris.
While water is running check all
connections for leaks. Reassemble the aerator
and screw it back into the spout hand tight.
3
GASKET & FAUCET INSTALLATION
A)
Apply a bead of plumber’s putty or silicone caulk around the sink openings.
B)
Install the gasket over the three holes in your sink.
C)
Install faucet shanks through the holes of the sink. Centre the faucet body on the sink.
Don’t use plumber’s putty on cultured marble or other composite sinks.
Putty will discolour the sink.
2
TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply valves. These are usually found under
the sink.
C
06-4205P | COLUMBIA
TWO HANDLE LAVATORY FAUCET
ATTACH THE HOT AND COLD SUPPLY LINES
Make connections to water lines (not included). Use 1/2” IPS faucet connections (1) and tighten
connections with wrench. Or use the supplied coupling nuts (3) with 3/8” O.D. ball-nose risers (2),
hand tighten only. Do not overtighten.
1 - HANDLE
2 - SCREW
1
2
3
3 - SLEEVE
4 - BONNET
5 - CARTRIDGE
WARNING: READ ALL
the instructions completely before beginning.
READ ALL
warnings, care and maintenance information.
Taymor recommends calling a plumber if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help?
Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST) 1-800-387-7064 for additional assistance or service.
THANK YOU
FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
OCT. 2017
