background image

 
 

TBS Installation Manual 

 

3D FLASH+

 

 

TBS 3D FLASH+ Mounting and Installation Guideline    

    TBS-061    

    Rev 11-2023

  

page 4 of 17

 

 

2

 

Legal and Safety Instructions 

 

Allowed Applications 

TBS  products  are  not  designed,  authorized  or  warranted  to  be  suitable  for  use  in  medical,  military, 
aircraft,  space  or  life  support  equipment,  nor  in  applications  where  failure  or  malfunction  of  a  TBS 
product  can  reasonably  be  expected  to  result  in  personal  injury,  death  or  severe  property  or 
environmental  damage.  TBS  accepts  no  liability  for  inclusion  and/or  use  of  TBS  products  in  such 
applications. 
 

 

Inspection of goods received 

If the packaging or product has been damaged in transport, or should you suspect that it may have a 
fault, the product must not be put into service. In this case, contact your TBS company representative. 
 

 

Installation and Servicing 

Installation, setup and servicing of our appliances must only be carried out by suitably trained personnel.  

 

Installation and electrical connections must only be made by correspondingly qualified specialists. 
The relevant national Electrical Engineers construction regulations must be observed.  

 

Setup and servicing must only be made by persons who have the know how to do so e.g. by 
reading the respective TBS manuals or attending TBS trainings / webinars.  

 
When not otherwise stated, the following safety instructions apply:  

 

Installation and servicing of our appliances must be carried out when disconnected from the 
power supply, in particular appliances that are normally supplied by low-voltage current.  

 

It is prohibited to alter the device or to remove protective shields and covers.  

 

Do not attempt to repair an appliance after a defect, failure or damage, or to put it back into 
operation again. Please contact in such case your TBS company representative or the TBS hotline.  

 
If there are still some points on which you are not entirely clear, please do not take a chance. All queries 
can be clarified by your TBS company representative, or by ringing the TBS hotline.  
 

 

 

Disclaimers 

TBS accepts no responsibility for any injuries or damage caused as a result of improper use.  

Information in this document is believed to be accurate and reliable. However, TBS does not give any 
representations  or  warranties,  expressed  or  implied,  as  to  the  accuracy  or  completeness  of  such 
information and shall have no liability for the consequences of use of such information. 

Should you discover any fault with  the product or in its documentation, or have any suggestions for 
improvement, please confidently approach your TBS company representative or TBS hotline.  

TBS  reserves  the  right  to  make  changes  to  information  published  in  this  document  at  any  time  and 
without notice.  

 

Summary of Contents for 3D FLASH+


















Reviews: