English
• 29 •
The machine must not be exposed to temperatures
lower than 0°C as the water in the circuits may freeze
(even if the tank has been emptied).
descalinG
The descaling process takes approx. 25 minutes.
Limescale builds up inside the machine during normal use. It needs
to be removed regularly as it may clog the water and coffee circuit of
your machine. The machine automatically indicates when it needs
descaling when the service indicator light (orange) is constantly
lit.
not doing this may ultimately make your machine
stop working properly, and in this case repair is nOT
covered by your guarantee.
We recommend using saeco descaling solution (sold
separately), whose formula has been designed to
respect the technical specifications of the machine, thus
ensuring its continued service in the long term and for its safe
and risk-free use. The descaling solution is to be disposed of
according to the manufacturer’s instructions and/or the
regulations in force in the country of use. The durgol descal-
ing solution also respects the technical specifications of the
machine.
Warning! never drink the descaling solution or any
products dispensed until the cycle has been com-
pleted. never use vinegar as a descaling solution.
1-
Turn the machine off by pressing the On/Off button .
2-
Check that the carafe is correctly inserted and that there is no
capsule in the compartment.
3-
Remove and empty the water tank, drip tray and used capsule
drawer.
4-
Pour the contents of the bottle of descaling solution into the
water tank and fill it with fresh water up to the MAX level.
5-
Put the tank back into the machine.
6-
Push the drip tray all the way into the machine and raise the
dispensing spout.
7-
Place a container with a minimum capacity of 1 litre under the
the coffee and milk dispensing spouts.
8-
At the same time, press the On/Off button (green) and the
Cappuccino button
(white) for 3 seconds, then release.
9-
The machine indicates that the process has started when the
service indicator light
(orange) is constantly lit; the Espresso
button
(white) will also be constantly lit to indicate the first
phase of the descaling operation.
during descaling, the On/Off button (green) will
not operate. If the power cord is removed, the machine
will continue the descaling cycle from the phase in which it was
interrupted the next time it is turned on.
10
- Press the Espresso button
(white) to start dispensing the
descaling solution.
The machine dispenses the descaling solution at regular intervals
via the coffee dispensing spout and via the carafe. The Espresso
button
(white) flashes throughout this first phase.
The cycle can be temporarily suspended by pressing
the rinse button
. Press it again to continue with
the descaling process.
11-
When the machine has run out of descaling solution, the service
indicator light (orange) flashes.
12-
Empty the container in which the descaling solution was collected
and reposition it under the milk and coffee dispensing spouts after
the drip tray has been emptied and replaced.
The Cappuccino button
will light up automatically.
13-
Remove the water tank and fill it up to the
maX level
with fresh
drinking water. Place the tank back in the machine.
14-
Press the Cappuccino button
to start the rinse cycle.
The machine dispenses the rinsing water alternately via the cof-
fee dispensing spout and via the milk carafe, with the Cappuccino
button
flashing throughout this phase.
If the tank is not filled up to the maX level, the service
indicator light (orange) continues to flash and the
machine will require another cycle to be performed; repeat
the process from step 13.
15-
When the second rinse cycle has finished, all the lights will flash
five times and the machine will turn off.
16-
Empty the container in which the rinsing water was collected.
17-
Empty the drip tray.
18-
Rinse and refill the water tank up to the MAX level.
19-
Rinse the milk carafe.
20-
When the machine is turned back on it will be ready to prepare
beverages again.
