SmartStuff Remote
Item Number: SMREMOTE
Smart Remote Button Instructions:
1
2
3
4
On
Off
Increase Brightness
Increase CCT
Reduce Brightness
Group 4 On
Group 4 Off
Group 3 On
Group 3 Off
Status Light
Reduce CCT
Group Select
Group 1 On
Group 1 Off
Group 2 On
Group 2 Off
4.32"
4.32
"
2.0"
2.0"
.875"
2.25"
.78"
ON :
Turns on all TCP SmartStuff devices connected to the APP.
OFF :
Turns off all TCP SmartStuff devices connected to the APP.
Increase Brightness:
Increases the brightness of the TCP SmartStuff
devices on a network or an individual group.
Decrease Brightness:
Decreases the brightness of the TCP SmartStuff
devices on a network or an individual group.
Increase CCT*:
Increases the color temperature of the TCP SmartStuff
devices on a network or an individual group.
Decrease CCT*:
Decreases the color temperature of the TCP SmartStuff
devices on a network or an individual group.
*
TCP SmartStuff devices must be capable of changing its color temperature for the buttons to work
Group Buttons Group (1, 2, 3, 4)
Group (1, 2, 3, 4) On:
Turns on all TCP SmartStuff devices connected to the APP.
Group (1, 2, 3, 4) Off:
Turns off all TCP SmartStuff devices connected to the APP.
Group (1, 2, 3, 4) Select:
Selects the corresponding group.
Switching Between Groups
Pressing on Group On, Group Off, or Group Select buttons will enable the Smart
Remote to control the corresponding group. Pressing the CCT or Brightness buttons
will affect the TCP SmartStuff devices in that group only. To change the Smart
Remote to control all the SmartStuff devices, press either ON or OFF. Setting up the
Groups must be done through the TCP Smart Stuff App.
HARDWARE NEEDED
• Electric Drill
• Philips Screw (size needed)
• Drywall Anchor (size needed)
• Ruler
• Pencil
1. Remove the Mounting Base from the Smart Remote.
2. Choose desired location of the Mounting Base.
3. Use a pencil to place a mark on the wall where each
Drywall Anchor will go.
4. Drill holes.
5. Place Drywall Anchor in wall.
6. Place Mounting Anchor on wall and screw in.
Resetting the TCP SmartStuff
Remote:
Programming the TCP SmartStuff
Remote:
325 Campus Dr. | Aurora, Ohio 44202 | P: 800-324-1496 | tcpi.com
TCP
®
©OCT 2020/WF220260
With the SmartStuff Remote:
• Press and hold “On” and “Increase Brightness” buttons for
3 seconds.
• The Status Light will slowly flash 3 times
• SmartStuff Remote has been reset to the Factory Setting.
With the SmartStuff Remote:
• Press and hold the “On” and “Reduce Brightness” buttons for 3 seconds.
• The Status Light will flash for 60 seconds.
With the TCP SmartStuff App:
• Go to the Add Accessory Screen.
• The SmartStuff App will scan for nearby SmartStuff Accessories that
can be programmed.
• Once the SmartStuff Remote has been found by SmartStuff App, it will show
up on the screen.
• Press the “Add Device” button on the SmartStuff App to complete
the programming.
TCP SmartStuff Remote can be used to turn on, off and dim all the devices
associated with it.
Dimensions:
1
2
3
4
On
Off
Increase Brightness
Increase CCT
Reduce Brightness
Group 4 On
Group 4 Off
Group 3 On
Group 3 Off
Status Light
Reduce CCT
Group Select
Group 1 On
Group 1 Off
Group 2 On
Group 2 Off
4.32"
4.32
"
2.0"
2.0"
.875"
2.25"
.78"
ON :
Turns on all TCP SmartStuff devices connected to the APP.
OFF :
Turns off all TCP SmartStuff devices connected to the APP.
Increase Brightness:
Increases the brightness of the TCP SmartStuff
devices on a network or an individual group.
Decrease Brightness:
Decreases the brightness of the TCP SmartStuff
devices on a network or an individual group.
Increase CCT*:
Increases the color temperature of the TCP SmartStuff
devices on a network or an individual group.
Decrease CCT*:
Decreases the color temperature of the TCP SmartStuff
devices on a network or an individual group.
*
TCP SmartStuff devices must be capable of changing its color temperature for the buttons to work
Group Buttons Group (1, 2, 3, 4)
Group (1, 2, 3, 4) On:
Turns on all TCP SmartStuff devices connected to the APP.
Group (1, 2, 3, 4) Off:
Turns off all TCP SmartStuff devices connected to the APP.
Group (1, 2, 3, 4) Select:
Selects the corresponding group.
Switching Between Groups
Pressing on Group On, Group Off, or Group Select buttons will enable the Smart
Remote to control the corresponding group. Pressing the CCT or Brightness buttons
will affect the TCP SmartStuff devices in that group only. To change the Smart
Remote to control all the SmartStuff devices, press either ON or OFF. Setting up the
Groups must be done through the TCP Smart Stuff App.
HARDWARE NEEDED
• Electric Drill
• Philips Screw (size needed)
• Drywall Anchor (size needed)
• Ruler
• Pencil
1. Remove the Mounting Base from the Smart Remote.
2. Choose desired location of the Mounting Base.
3. Use a pencil to place a mark on the wall where each
Drywall Anchor will go.
4. Drill holes.
5. Place Drywall Anchor in wall.
6. Place Mounting Anchor on wall and screw in.
Smart Remote Button Descriptions: