background image

REV 1.6 

 

     © 2019 TCW Technologies, LLC. 

20 

 

 

 

TCW Technologies, LLC. 
 
During the first 12 months from the date of purchase and subject to the conditions hereinafter set forth, TCW Technologies, 
LLC. (TCW) will repair or replace to the original user or consumer any portion of your new TCW product which proves 
defective due to defective materials or workmanship of TCW.  Contact TCW Technologies for warranty service. TCW shall 
have and possess the sole right and option to determine whether to repair or replace defective equipment, parts or components. 
Damage due to equipment, environment or conditions beyond the control of TCW Technologies are NOT COVERED BY 
THIS WARRANTY. 
 
  
LABOR, COSTS: TCW shall IN NO EVENT be responsible or liable for the cost of field labor or other charges incurred by 
any customer in removing and/or reaffixing any TCW product, part or component thereof. 
 
THIS WARRANTY WILL NOT APPLY: (a) to defects or malfunctions resulting from failure to properly install, operate or 
maintain the unit in accordance with printed instructions provided; (b) to failures resulting from abuse, accident, or negligence; 
(c) to normal maintenance services and the parts used in connection with such service; (d) to units which are not installed in 
accordance good trade practices; or (e) to unit used for purposes other than for what it was designed and manufactured.  

 
RETURN OR REPLACED COMPONENTS: any item to be replaced under this Warranty must be returned to TCW 
Technologies in Emmaus, PA, or such place as TCW may designate, freight prepaid. 
 
PRODUCT IMPROVEMENTS: TCW reserves the right to change or improve its products or any portions thereof 
without being obligated to provide such a change or improvement for units sold and /or shipped prior to such 
change or improvement. 
 
WARRANTY EXCLUSIONS: as to any specific TCW product, after the expiration of the time period of the warranty 
applicable thereto as set forth above. THERE WILL BE NO WARRANTIES, INCLUDING ANY IMPLIED 
WARRANTIES OR MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. 
 
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to 
you. No warranties or representations at any time made by any representative of TCW shall vary or expand the 
provisions hereof. 
 
LIABILITY LIMITATION: IN NO EVENT SHALL TCW OR ITS AFFILIATES BE LIABLE OR RESPONSIBLE FOR 
CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER 
TO ANY TCW PRODUCT OR PARTS THEREOF. THE SUITABILITY OF USE OF THE TCW TECHNOLGIES, 
LLC. PRODUCT IS TO BE DETERMINED BY THE AIRCRAFT BUILDER. 
 
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation 
or exclusion may not apply to you. 
 
This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. In 
the absence of other suitable proof of this installation date, the effective date of this Warranty will be based upon the 
date of manufacture plus one year. Direct All Notices To: Warranty and Product Service Department, TCW 
Technologies, 2955 Main Road East. Emmaus, PA 18049 

 

 

 

 

Summary of Contents for IBBS-12V-AH





















Reviews: