TDI TURBOTWIN T100-MS Installation And Operating Manual Download

Page: 6 / 11

TDI

URBO

WIN

™

FROM

TECH DEVELOPMENT

Publication: T1-795
Issued: August 1, 2008

Page 5

2.1 PROPER INSTALLATION, ORIENTATION & OIL LEVEL MAINTNENACE

OLAR P/N: 1078362-100

SOLAR P/N1078362-200

Motor/Starter Gearbox must be filled w/ (150ML) of Approved Oil Type** & Level Maintained

** Oil Type Recommended

: Spec MIL-L-7808H, MIL-L-23699

(or equivalent synthetic grade turbine oil)

OIL FILL PORT

½”-14 NPT

OIL LEVEL

SIGHT GLASS

ORIENTATION

Viton O-ring
seal beneath 2”
NPT inlet flange

Viton O-ring seal
beneath 3”
exhaust adapter
flange

NOTE: PROPER INSTALLATION -
OIL LEVEL SIGHT GLASS
POSITIONED PARALEL TO
GROUNDLINE & BELOW
STARTER/MOTOR CENTERLINE

Starter
Output Shaft
& Mating
Spline
Engine Aux.
Gearbox

Splash-lube
Gearbox

Summary of Contents for TURBOTWIN T100-MS












Search results

Summary of Contents for TURBOTWIN T100-MS

Reviews:

Related manuals for TURBOTWIN T100-MS

Brands by name

Popular brands

TDI TURBOTWIN T100-MS, Installation And Operating Manual

Search results

Summary of Contents for TURBOTWIN T100-MS

Reviews:

Related manuals for TURBOTWIN T100-MS

Brands by name

Popular brands