background image

INSTRUCTION MANUAL

EZA2500FC

TDK-Lambda

<Page>

6-2. 

Automatic Grid CV mode

Grid voltage is maintained at set target voltage. 
If grid voltage is lower than the target voltage : 
Regeneration Operation 

Discharge

If grid voltage is higher than the target voltage:
Generation Operation (Charge)
There is a dead zone (power conversion non-operational 
band) which can be set between regeneration voltage level 
and generation voltage level.
Constant current control is for grid side current both 
generation operation and regeneration operation.
For generating operation and regenerating operation the 
target current value can be set separately. 

6-3. 

Automatic Grid CV with Battery CC mode

The basic actions of this mode is same to Grid 
Automatic CV Mode.  Constant current is controlled by 

battery side current.

Also, it is possible to set battery over-charge and over-discharge protection that stops charging and discharging process 
when battery voltage level reaches the target voltage level. (Refer to 7.Battery Protection)
For the Output Side (Grid Port), 300V or more pre-charge is required. When external voltage is not applied, this 
converter will not operate.

7/23

Target Grid Voltage

Vgrid

Ibat

Grid Under Voltage

Grid Over Voltage

ShutDown

ShutDown

Regeneration

(Discharge)

Generation

(Charge)

Battery Limit Current

Battery imit Current

0

Operating Characteristic

Deadzone

Deadzone Upper Limit Voltage

Deadzone Lower Lomit Voltage

Converter

320V (HVDC)

48V (LVDC)

Output

(Grid)

Input

(Battery)

Generation

(Charge)

Regeneration

(Discharge)

Ibat

Vgrid

Converter

320V (HVDC)

48V (LVDC)

Output

(Grid)

Input

(Battery)

Generation

(Charge)

Regeneration

(Discharge)

Igrid

Vgrid

Target Grid Voltage

Vgrid

Igrid

Grid Under Voltage

Grid Over Voltage

ShutDown

ShutDown

Regeneration

(Discharge)

Generation

(Charge)

Grid Limit Current

Grid Limit Current

0

Operating Characteristic

Deadzone(*)

Deadzone Upper Limit Voltage

Deadzone Lower Lomit Voltage

*Deadzone : Converter is held in equilibrium operation 

that no operation neither generate nor regeneration.

Summary of Contents for EZA2500FC
























Reviews: