background image

B-3

W

ArrAnty

 S

tAtement

Manufacturer shall not have any liability to the Distributor under any provision of this clause if any infringement, 

or claim thereof, is based upon: (i) the use of the goods in combination with other goods or devices which are 

not made by Manufacturer; (ii) the use of the goods in practicing any process; (iii) the furnishing to the Distribu-

tor of any information, date, service, or applications assistance; or (iv) the use of the goods with modifications 

made by the Distributor.  The Distributor shall hold Manufacturer harmless against any expense, judgment or 

loss for infringement of any patent or other intellectual property right which results from Manufacturer’s com-

pliance with the Distributor’s designs, specifications or instructions.  No costs or expenses shall be incurred for 

the account of Manufacturer without the written consent of Manufacturer.  

THE FOREGOING STATES THE 

ENTIRE LIABILITY OF MANUFACTURER WITH RESPECT TO INFRINGEMENT OF PATENTS 

OR OTHER INTELLECTUAL PROPERTY RIGHT BY THE GOODS OR ANY PART THEREOF, OR 

BY THEIR OPERATION.

In the event that a final injunction shall be obtained against the Distributor’s use of the goods or any of their 

parts by reason of infringement of a patent or other intellectual property right or if in Manufacturer’s opinion 

the goods are likely to become the subject of a claim of infringement of a patent or other intellectual property 

right, Manufacturer will, at its option and at its expense, either procure for the Distributor the right to continue 

using the goods, replace or modify the same so they become non-infringing or grant the Distributor a credit for 

such goods as depreciated and accept their return.  The depreciation shall be an equal amount per year over the 

lifetime of the goods as established by Manufacturer. 

d

efenSe

 

of

 i

nfringement

 c

lAimS

If notified promptly in writing of any action (and all prior claims relating to such action) brought against the 

Distributor based on a claim that Distributor’s use of the goods infringes a patent or other intellectual property 

right, and if given access by Distributor to any information distributor has regarding such alleged infringement, 

Manufacturer agrees to defend Distributor in such action at its expense and will pay any costs or damages finally 

awarded against Distributor in any such action, provided the Manufacturer shall have had sole control of the 

defense of any such action and all negotiations for its settlement or compromise.  

Summary of Contents for Triton VersaSafe



























Reviews: