TE Connectivity 2000739-1 Application Specification Download

Page: 6 / 13

114-13233

Rev B

of 13

3.10.

Installation of Backshell Assembly

(See Figure 5)

Place one side of the backshell on the back of the connector aligning the rib on the housing with the

groove in the backshell. Make sure that the backshell is on top of the last gland of the sealing boot/plug.

NOTE

Make sure the screw threads are recessed into the strain relief clamp to prevent interference with the housing during

assembly.

Repeat step 1 with the other half of the strain relief clamp.

Using a 5/64-in. Allen wrench, tighten the captive screws.

Apply two cable ties through the backshell as shown.

Figure 5

Captive Screws

Recessed for

Assembly

Seal Gland

Under Backshell

Backshell

Retention Rib

Cable Ties (Customer Supplied)

Captive Screws Thread

into Housing

Retention Rib in

Backshell Groove

Summary of Contents for 2000739-1














Search results

Summary of Contents for 2000739-1

Reviews:

Related manuals for 2000739-1

Brands by name

Popular brands

TE Connectivity 2000739-1, Application Specification

Search results

Summary of Contents for 2000739-1

Reviews:

Related manuals for 2000739-1

Brands by name

Popular brands