background image

  Te Pari - www.tepari.com - FREEPHONE 0800 837 274  

HD3 Sheep Handler Installation Manual     

1214-V1

18

Racewell HD 

SHEEP HANDLING SYSTEMS

SETTING UP A GALLAGHER SMARTSCALE 800

Switch the main dial to  

 for set up

DRAFT MENU 

 will display, press the 

SELECT

   soft key

DRAFTING OFF

  is usually displayed, press the 

MODE

   soft key until

3 WAY DRAFTING 

is displayed, each time you press the 

MODE

   soft key it will

cycle through the options from  

DRAFTING OFF  

to  

9 WAY DRAFTING

 

Press the  

  soft key and set your draft limits for each gate 

To change either a gate number or draft limit use the backspace button  

  to clear the existing 

entry, then key in the new number using the keypad  
Note: Draft limits - always put the lesser value at the top and the larger value at the bottom 

When done, press the 

OK

   soft key

1. DRAFT MENU 

 will display, as you are still in set up, press the 

  soft key until 

5. COMMUNICATIONS

 is displayed, press the 

SELECT

   soft key 

If not highlighted already, press the 

 soft key to highlight the

 Port 1 

screen entry, press the 

CHANGE

 soft key until the 

Drafter Fast 

option is displayed for it 

Press the 

OK

   soft key to save your changes and return to the set up menu 

Switch the mode select switch to  

A

  (automatic weight recording) and test your settings 

A

M

F

S

Off

Automatic weight recording

Manual weight recording

Fine - To weigh static loads

Set up options

Mode select switch

 Switch and scale colour may vary

Summary of Contents for Racewell HD3



























Reviews: