−
19
−
17. Focus balance setting value of L0
18. Focus balance setting value of L1
19. Current mechanism controller inside mode
(it does not support in this unit)
It can indicate to a maximum 10 modes. Indicate only a nest
share of the mode.
20. Processing step of 11 inside modes
(it does not support in this unit)
It can grasp the current mode, the mode reaching it and
transition of step by watching 19 and 20.
21. Spindle control state of SCRUT (IC701)
(it does not support in this unit)
OFF
: Motor off condition
A/B
: Accelerator and brakes
FG
: FG servo
RVP : Rough speed phase servo
ORVP : Rough speed phase servo of offset addition
22. Rotation number of spindle motor
Do not FG read in ? indication (during spindle stop).
23. Tracking error generation system
(it does not support in this unit)
1 : 1 beam (DPD)
3 : 3 beams
24. TZC count value (it does not support in this unit)
The value that counted the number of TZC for one rotation in
the tracking open state.
When this value is more than 512 with CD, set it in 1 beam
because the eccentric is large.
DVD does not measure it because it is 1 beam fixed
(indication is 0000).
25. It indicates the frequency that entered the focus backup
Hexadecimal number indication. Counter does not reset till
turns the power off after turning it on. Due to a 1 byte
counter, next of FF becomes 00.
26. It indicates focus backup limit frequency with the
hexadecimal number
Initial value is 14H, it does decrement whenever enter the
focus backup and it gives up backup if it became 0. Then the
error is generated. After reverted from the backup, When not
enter the backup and pass fixed time (1500ms), return to
initial value again.
27. It indicates the frequency that entered the internal
circumference plunging into backup of the sled
Hexadecimal number indication. Counter does not reset till
turns the power off after turning it on. Due to a 1 byte
counter, next of FF becomes 00.
17. L0のフォーカスバランス設定値
18. L1のフォーカスバランス設定値
19. 現在のメカコン内部モード(本機では対応していません)
最大10モードまで表示できる。モードのネストの分だけ表
示する。
20. 11の内部モードの処理ステップ(本機では対応していませ
ん)
19と20を見ることにより、現在のモードとそれに至るま
でのモード、ステップの遷移を把握することができる。
21. SCRUT (IC701)のスピンドル制御状態(本機では対応し
ていません)
OFF
:モータオフ状態
A/B
:アクセル・ブレーキ
FG
:FGサーボ
RVP
:ラフ速度位相サーボ
ORVP :オフセット加算ラフ速度位相サーボ
22. スピンドルモータの回転数
?表示時はFG読みとりをしていないとき(スピンドル停止
中)。
23. トラッキングエラー生成方式(本機では対応していません)
1 :1ビーム(DPD)
3 :3ビーム
24. TZCカウント値(本機では対応していません)
トラッキングオープン状態で1回転分のTZCの数をカウン
トした値。
CDでこの値が512以上の時は偏芯大なので1ビームにす
る。
DVDは1ビーム固定なので測定しない(表示は0000)。
25. フォーカスバックアップに入った回数
16進表示。カウンタは電源を入れてから電源を切るまでリ
セットしない。1バイトカウンタなので、FFの次は00にな
る。
26. フォーカスバックアップ制限回数
16進表示。初期値は14Hでフォーカスバックアップに入る
たびにデクリメントしていき、0になったらバックアップを
諦めエラーを発生する。バックアップから復帰後、バック
アップに入ることなく一定時間(1500ms)経過すると再
び初期値に戻る。
27. スレッド内周突っ込みバックアップに入った回数
16進表示。カウンタは電源を入れてから電源を切るまでリ
セットしない。1バイトカウンタなので、FFの次は00にな
る。
Summary of Contents for Esoteric DV-50
