T O O L S U S E D
HUB CARRIERS TO REAR ARMS
Place the left hub carrier between the arm holes as shown and
add two #6466 spacers where shown.
Add a #6299 E-clip to the #9263 hinge pin insert it as shown,
then add an E-clip at the other end of the hinge pin.
Insert the universal dog bone into the slots of the outdrive hub.
Now install the axle assembly for the right side.
ASSEMBLE THE #9276 MIP CVD
TM
(Constant Velocity Drive
TM
)
Spread some Associated #6588 black grease inside the #7380 axle hole where shown, then on
the #7381 coupling, and insert the coupling into the axle.
Slide the axle into the #9278 dogbone, aligning the cross holes.
Insert the #7381 cross pin, making sure it is evenly spaced on both sides of the #9278 bone.
Add the #9276 MIP thread lock to the #7381 set screw. Angle and turn the MIP CVD
TM
so the
set screw can be screwed in with the Allen wrench.
Assemble the other axle.
7368
6272
6273
3977
7260
7366
7369
3977
7380
6466
1/16"
Be careful not to damage
the indented shields of the
ball bearings when pushing
them in.
6273, qty 2
ball end
B A G E
1 : 1
1:1
6272, qty 2
dust cover
1:1
1:1
1:1
1:1
1:1
6299, qty 4
E-clip
6466, qty 4
spacer, 1/16"
7260, qty 2
small nut
9263, qty 2
rear outer hinge pin
1:1
7377, qty 2
rear axle
bearing spacer,
aluminum
1:1
7368, qty 6
3/16" axle shim,
steel
7369, qty 2
axle spring
pin
1:1
1:1
T E A M & F A C T O R Y T E A M K I T S O N L Y
s t e p 1
L E F T S I D E
13
7377
3977, qty 4
3/16 x 3/8
ball bearing
REMOVE THESE
PARTS FOR:
Team: step 1
Factory Team:
step 1
7366, qty 2
hub carrier
9257,
9258*
6299
9263
6299
9263
R E A R
7366
REAR HUB CARRIERS
Note that the #7366 hub carriers are marked left and right. Slide one of
the thin #7368 3/16" axle shims onto the axle.
Install one #3977 bearing, then the #7377 bearing spacer. NOTE: You
MUST use the bearing spacer. Slide the axle assembly into the hub
carrier from the rear.
Install the second #3977 bearing into hub carrier and onto the axle,
followed by the #9276 thick spacer and two #7368 thin spacers. Insert
the #7369 roll pin into axle.
Thread on the #6273 ball end into the hole shown and add the #7260 nut
to the other side.
(When you do the other hub carrier, thread the ball end
into the other side so both ball ends will point to the front when
assembled.)
Add a #6272 dust cover to the ball end.
Follow the above for the right hub carrier.
7381
cross pin
9278
9276
7381
7381
coupling
7380
6588
6588, qty 1
black grease
9276, qty 1
MIP threadlock
9278, qty 2
CVD dog bone
7380, qty 2
CVD axle
3438, qty 2
8-32 locknut
1:1
1:1
7381, qty 2
CVD coupling
1:1
7381, qty 2
CVD cross pin
1:1
7381, qty 2
CVD set screw
.050"
9276, qty 2
3/16" axle shim
MIP thick, steel
1:1
6466
1/16", 2
7368
9276
7380
T E A M & F A C T O R Y T E A M K I T S O N L Y
make sure window
faces front
5
9
5
