background image

EN

3

LOSI 8IGHT  • INSTRUCTION MANUAL

• 

1/8-Scale High Performance Gasoline Buggy

• Spektrum

 DX2E 2.4GHz DSM

®

 Radio System

• Dynamite

®

 .31 ci Gasoline Engine

• 

Spektrum High-Torque Servos

• 

4 AA batteries (for transmitter)

• 

Spektrum 7.4V 1300mAh Li-Po receiver pack.

• 

Losi Starter Box

Tools Included

• Wheel 

wrench

• 

Four (4) Hex “L” Wrench Set: .050-inch, 1/16-inch, 5/64-inch and 3/32-inch

• 

Shock Bottom wrench

• Turnbuckle/Shock 

Top 

wrench

• 

Spark Plug Wrench (DYNT1250)

Needed to Complete

• 

91 Octane Gasoline

• Gasoline 

Approved 

Dispenser

• 

2 x 6 cell NIMH Battery (DYN1050)

• 

Small fl at blade and Phillips screwdrivers (DYNT2100 and DYN3048)

• Needle-nose 

pliers

• 

Quality .050-inch, 1/16-inch, 5/64-inch, 3/32-inch, 1.5mm and 2.5mm hex 
(Allen) drivers (DYN2950)

Use only Dynamite

 

tools or other high-quality tools. Use of inexpensive tools 

can cause damage to the small screws and parts used on this type of model.

Your new Horizon Hobby vehicle has been designed and built with a combination of 
waterproof and water-resistant components to allow you to operate the product in 
many “wet conditions”, including puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely waterproof 
and your vehicle should NOT be treated like a submarine. The various electronic 
components used in the vehicle, such as the servo(s) and receiver are waterproof, 
however, most of the mechanical components are water-resistant and should not be 
submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the 
contacts in the electrical cables, will be susceptible to corrosion if additional 
maintenance is not performed after running in wet conditions. To maximize the long-
term performance of your vehicle and to keep the warranty intact, the procedures 
described in the “Wet Conditions Maintenance” section below must be performed 
regularly if you choose to run in wet conditions. If you are not willing to perform the 
additional care and maintenance required, then you should not operate the vehicle in 
those conditions.

CAUTION:

 Failure to exercise caution while using this product and 

complying with the following precautions could result in product 
malfunction and/or void the warranty.

GENERAL PRECAUTIONS

• 

Read through the wet conditions maintenance procedures and make sure that you 
have all the tools you will need to properly maintain your vehicle.

• 

Not all batteries can be used in wet conditions. Consult the battery manufacturer 
before use. Caution should be taken when using Li-Po batteries in wet conditions.

• 

Most transmitters are not water-resistant. Consult your transmitter’s manual or the 
manufacturer before operation.

• 

Never operate your transmitter or vehicle where lightning may be present.

• 

Do not operate your vehicle where it could come in contact with salt water (ocean 
water or water on salt-covered roads), contaminated or polluted water. Salt water is 
very conductive and highly corrosive, so use caution.

• 

While the air fi lter assembly can be designed to limit or restrict water ingestion into 
the engine, no air fi lter is completely waterproof. If too much water is ingested into 
the engine, severe damage to the engine may result.

• 

Do not expose your engine to rapid changes in temperature. These engines 
tend to operate at temperatures between 200–265°F (93–129°C) in normal 
operating conditions. If the engine is exposed to cold water while operating at this 
temperature, there is a risk of “thermal shock”, which could cause undue stress on 
the engine and a shortened engine lifespan.

• 

Driving in wet conditions can reduce the life of the engine. The additional 
resistance of operating in water causes excess strain. Alter the gear ratio by using 
a smaller pinion or larger spur gear. This will reduce the load on the engine (and 
engine temperatures) when running in mud, deeper puddles, or any wet conditions 
that will increase stress on the engine for an extended period of time.

Wet Conditions Maintenance

• 

Remove the battery pack(s) and dry the contacts. If you have an air compressor 
or a can of compressed air, blow out any water that may be inside the recessed 
connector housing.

• 

Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with 
a garden hose. Avoid rinsing the bearings and transmission.

NOTICE: 

Never use a pressure washer to clean your vehicle.

• 

Use an air compressor or a can of compressed air to dry the vehicle and help 
remove any water that may have gotten into small crevices or corners.

• 

Spray the bearings, drive train, fasteners and other metal parts with a water-
displacing light oil or lubricant.

• 

Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a 
few hours.

• 

Increase the frequency of disassembly, inspection and lubrication of the following: 

•  Front and rear axle hub assembly bearings.
•  All transmission cases, gears and differentials.
•  Engine air fi lter element.
•  Engine clutch assembly, including shoes and bearings.

Water-resistant Vehicle with Waterproof Electronics

Components

Summary of Contents for 8IGHT






























Reviews: