background image

2

Losi/Horizon Support

If you have any questions concerning setup or operation 

of your Speed-NT RC vehicle please call Horizon Customer 

Support at 1-877-504-0233.
Hours: 

Monday thru Friday from 8:00am CST to 5:00pm CST
You are welcome to call us with any support issue, or question 

you may have about the Speed-NT.

Getting Ready

Thoroughly read all the enclosed material, precautions and 

follow instructions to avoid damaging your new RC vehicle. If 

you choose to not follow these steps or instructions, it will be 

considered negligence.
If after review of this manual and prior to running your Speed-

NT, you determine this RC vehicle is not what you want—DO 

NOT proceed and DO NOT run the Speed-NT. If the Speed-NT 

has been run, your local hobby shop will not be able to process 

a return or accept it for exchange.

Caution:

Age Recommendation: 14 years or over. This is not a toy. This 

product is not intended for use by children without direct adult 

supervision.
This vehicle is capable of extreme speed and careful attention 

and care must be used when operating the Speed-NT. 
When driving the Speed-NT it is important that you take 

measures to avoid someone being hit by the vehicle. You may 

cause serious injury to another person, or to personal property 

should you make contact while running the Speed-NT.

Introduction

Thank you for choosing the Speed-NT. This is a highly 

developed RC model that features a sophisticated radio 

system and a nitro fuel powered engine. It does require some 

mechanical experience and direct adult supervision. This guide 

contains the basic instructions and drawings needed to operate 

and maintain your new Speed-NT. Please take the time to read 

through these instructions completely before attempting to 

run your new model. Your hobby dealer cannot under any 

circumstances accept a model for return or exchange that has 

been run. We are confident you will be satisfied with the high-

speed performance in this durable and resilient vehicle. 
Understanding that you are anxiously wanting to get your 

Speed-NT ready for the open road, it will be to your long term 

benefit to make the effort and read through the entire manual. 

In the following pages you will find all the information you will 

need to set up as well as operate your new Speed-NT to its full 

potential.

If you are an experienced RC hobbyist, or new to RC vehicles, 

it will benefit you to read all enclosed information.

From everyone at Losi we would like to thank you again for 

choosing the Speed-NT. Our goal is helping people have fun 

and enjoy using our products.

Register your Losi Product Online

Register your Speed-NT now and be the first to find out  

about the latest options parts, product updates and more.  

Log on to www.LOSI.com and follow the product registration 

link to stay connected.

Summary of Contents for Speed NT

























Reviews: