6 - EN
6 -
E
6 -
E
EN
N
EN
N
Servo
Manufacturer
,
Make
/
Mode
l
Servo
Spacer
Servo
Horn
J
R
A
ll
(D
Z
9
1
00
T
/S
Needs
Spa
c
er)
No
23
T
Air
tr
onics
Sa
n
w
a
94357
Z
,
94358
Z
,
94649
Z
,
94360
Z
,
94452
Z
,
94758
Z
,
94737
Z
,
94738
Z
Yes
23
T
94
1
02
Z
,
94
11
2
Z
Yes
Hit
e
c
A
ll
No
24
T
F
utaba
A
ll
(S9
1
02
DOES
NO
T
FI
T
)
No
25
T
K
O
PROPO
PDS-2
1
23,
2344,
2363,
2365,
2366
No
23
T
No
Before Running Your TEN-SCTE
Before Running Your TEN-SCTE
1.
Break in the diff erentials. While holding the chassis with
only the left side tires fi rmly on the ground, give the car
about one eighth throttle, for 30 seconds. The right side
tires should spin freely during this time. Repeat this with
only the right side tires fi rmly on the ground, allowing the
left side tires to spin freely. Repeat this 2–3 times.
2.
Check for free suspension movement. All suspension arms
and steering components should move freely. Any binds
will cause the car to handle poorly.
3.
Set the ride height. Set the ride height of your truck with
all components installed so that the bottom of the chassis
is 29.5mm from the ground in the front and 24.5mm in the
rear by adjusting the shock collars.
4.
Set the camber. Adjusting the camber tie rod length
changes the camber. Set the front tires to have 0 degrees
of camber at ride height. Set the rear tires to have 2.5
degrees of negative camber at ride height.
5.
Set the front toe-in. Adjust the steering tie rods so that
when the servo is centered on the transmitter, the front
tires are both pointing straight.
6.
Charge a battery pack. Charge a battery pack as per the
battery manufacturers and/or charger manufacturers’
instructions.
7.
Adjust the electronic speed control. Follow the
manufacturers instructions to setup and adjust the speed
control for your TEN-SCTE.
8.
Set the transmitter steering trim. Follow the manufacturers
instructions to set the steering trim/subtrim so that the
vehicle goes straight with no input to the steering.
9.
Set the transmitter steering endpoints. Follow the
manufacturers’ instructions to set the endpoints so that
the servo hits full steering upon reaching full input from
the transmitter.
Driving the TEN-SCTE
Driving the TEN-SCTE
Always follow these precautions when running your TEN-
SCTE.
Do not run the TEN-SCTE at dusk or in the dark when
visibility is limited.
Do not attempt to run this model if it will be out of sight for
any amount of time.
Do not run this model near a crowd of people.
Always check for proper radio function and battery condition
before operating.
Check to make sure the tires are securely glued to the rims.
Check the model thoroughly for loose nuts
,
bolts and screws
before and after running.
Make sure you use proper dirt tires if running off -road.
Never run the model with old or discharged batteries.
Leave plenty of room to stop the model. It will take as much
room to stop as it did to accelerate.
Summary of Contents for TEN-SCTE
