EN
4
TENACITY-DB PRO RTR, AVC: 1:10 4WD DESERT BUGGY • INSTRUCTION MANUAL
1
2
3
4
5
6
7
8
10
11
9
12
13
SR6100AT AVC TECHNOLOGY TELEMETRY RECEIVER
INSTALLING THE BATTERY
INSTALLING THE TRANSMITTER BATTERIES
1. Push in the battery cover a small amount to release the retaining tab, then remove the cover.
2. Install 4 AA batteries, taking care to align the battery polarity to the diagram in the
transmitter’s battery case.
3. Carefully reinstall the battery cover by aligning the tabs with the slots on the transmitter.
CAUTION:
If using rechargeable batteries, charge only rechargeable batteries.
Charging non-rechargeable batteries may cause the batteries to burst, resulting in
injury to persons and/or damage to property.
CAUTION:
Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to national regulations.
For more information on the transmitter, go to www.horizonhobby.com and click on the
support tab for the Spektrum DX2E to download the instruction manual.
AUX CHANNELS
The Aux channels can operate as additional servo channels, or as a power supply
for a personal transponder.
If AVC is active, only 4 channels; Steering, Throttle, AUX3 and AUX4 are operational.
The reaming Aux channels can be used to power a personal transponder or lights.
If AVC is disabled (see DISABLING AVC TECHNOLOGY STABILITY ASSIST FUNCTION),
all 6 channels including the Aux channels can operate as servo channels.
SPEKTRUM DX2E ACTIVE RADIO SYSTEM
AUX 1 Port
AUX 2 Port
AUX 3 Port
AUX 4 Port
Battery/Programming Port
Throttle Port
Steering Port
Bind Button
1. Steering
Wheel
Controls direction (left/right) of the model
2. Throttle
Trigger
Controls speed and direction (forward/brake/reverse) of the model
3. BIND
Button
Puts the transmitter into Bind Mode
4. ON/OFF
Switch
Turns the power ON/OFF for the transmitter
5. TH.REV
Reverses function of the speed control when pulled back or pushed forward
6. Indicator
Lights
-
Solid green light
—indicates adequate battery power
-
Flashing green light
—indicates the battery voltage is critically low. Replace batteries
7. ST.
REV
Reverses the function of the steering when the wheels is turned left or right
8. ST
Trim
Adjusts the steering center point
9. TH
Trim
Adjusts the throttle neutral point
10. TH Limiter
Limits throttle output to 50, 70 or 100%.
11. 3-Position Switch
Used to control a third channel and is preset at -100%/Neutral/100%
12. ST Rate
Adjusts the sensitivity of AVC technology
13. Antenna
Transmits the signal to the model
1. Ensure the ESC is powered OFF.
2. Remove the body clips and rotate the body up.
3. Remove the body clip from the battery hold down and open the battery tray.
4. Insert the battery into the battery tray.
5. Rotate the battery strap down, and insert the body clip to secure the battery.
6. Connect the battery power lead to the ESC, noting proper polarity.
7. Power ON the transmitter, then the vehicle.
8. Rotate the body into place, and insert the body clips.
IMPORTANT:
Secure the ESC wires so they do not interfere with the gearing.
3S battery spacers
The vehicle is setup at the factory for use with
a 2S LiPo battery. To install an optional 3S LiPo
battery, the included spacers must be added to
the battery tray as shown.
NOTICE:
If you are using a 2S Li-Po battery,
use the included 17T Pinion gear. If you are
using a 3S Li-Po battery, use the optional 15T
pinion gear (included). Using a 17T pinion gear
with a 3S Li-Po battery will result in damage to
the ESC and motor.
