Team Losi XXX-NT AD2, Owner'S Manual

53

TIPS FR

TIPS FR

TIPS FR

TIPS FR

TIPS FROM 

OM 

OM 

OM 

OM  THE 

THE 

THE 

THE 

THE  TEAM

TEAM

TEAM

TEAM

TEAM

TUNING THE ENGINE- should be done following the manufactures instructions.

By turning the needle valve clockwise, the fuel mixture will become leaner – meaning that the engine will draw less fuel. When the needle

valve is turned counter-clockwise, the fuel mixture becomes richer- meaning that the engine will draw more fuel. The high speed needle affects

the fuel mixture at mid tofull throttle while the low sped needle only affects the fuel mixture at idle and the low end of the throttle band.

THE AIR FILTER- pre-filter should be changed when it becomes covered with dust or dirt. The cleaner the filter remains, the better the

engine can breathe and run. If the air filter is allowed to become too dirty some of the dust or dirt can find its way into the engine and cause

problems. If the air cleaner should ever come off while operating your truck, stop immediately. Reattach the air filter before continuing! Never

run without an air filter, use a Tie Strap to secure the filter from coming off.

OILING THE FOAM PRE-FILTER Is essential to keep dust from entering the paper air filter element and potentially finding its way into the

engine. Good filter oil can be found in most automotive sections or motorcycle shops. These specialty oils are very sticky and will attract and

hold the dust on the foam. When using this type of oil, be careful not to over oil the foam. Squeeze out any excess oil before installing the foam

pre-filter over the paper element. Never oil the paper element. When the foam needs cleaning wash it out using one of the specialty foam filter

cleaners or a light detergent like Simple Green. Be sure to rinse away any residual cleaner and let the foam dry before oiling and reinstalling it.

TO SHUT THE ENGINE OFF-, simply bump flywheel with wrech or plastic tool handle, never use your finger.

THE RECEIVER BATTERY is an important, frequently overlooked part of gas-powered vehicles. It is important that the batteries always

have a fair amount of charge remaining in them. A low receiver battery can cause the truck to have a mind of its own. The result can be a runaway

truck or a poor responding radio system. If using alkaline batteries, a fresh set should operate the radio system for at least 1-2 hours of running

without a problem. The length of time that a receiver battery pack's charge lasts depends on the type of servos that are used. Some of the high

performance servos draw more current than standard servos, and will drain the receiver pack faster. Just remember to check the receiver pack

from time to time. When the servos start to operate a little slower, or radio response feels sluggish, the batteries probably need to be replaced.

If you will be using a Nicad or NiMH receiver pack, it is recommended that a minimum battery size of 1000 mAh and minimum voltage of 4.8

volts be used. A Nicad battery will not operate the radio system as long as an alkaline battery. The Nicad battery should be charged before every

day's outing with your truck, and after about every 45 minutes to 1 hour of operation. If  you are planning on racing a long main event, be sure

to charge the battery pack before the start of the main.

ATTACHING THE RECEIVER to the center brace with the thick double sided servo tape provided in the kit. This will help absorb the

shock and vibration that is transmitted through the chassis by the engine. This type of Servo Tape avaible from Team Losi, LOSA4004, can be

FINAL CHECKLIST

FINAL CHECKLIST

FINAL CHECKLIST

FINAL CHECKLIST

FINAL CHECKLIST

BEFORE RUNNING YOUR XXX-NT AD2 for the first time, you should run down the following checklist — in order — and complete the listed

tasks. This simple checklist will help to make the first run with your new XXX-NT AD2 truck much more enjoyable.

          1. Adjust the rear differential-

Never let your Differential Slip! See Adjusting The Differen-

tial in the tips section.

          2. Check for proper radio linkage adjustments

Refer to the Radio Installation section one last time and en-

sure that all linkages and collars are properly adjusted.

          3. Check for free suspension movement

All suspension arms should be very free. Any binds will

cause the truck to handle poorly. The steering should also

operate very freely.

          4. Set the rear ride height

The rear ride height should be set so that the arms are level

with the surface, with fuel. See the Rear Ride Height section

of the tips.

          5. Set the front ride height

The front ride height should be set so that the front suspen-

sion arms are level with the surface, with fuel.

          6. Adjust the camber

The front camber should be set to 1-1/2 degrees of negative

camber (top of tire leans in) at ride height. Adjust the front

camber with the tires straight. The rear camber should be set

to 0-1 degrees of negative camber at ride height.

          7.  Adjust toe-in/toe-out

The front tie rods should be adjusted evenly until the front

tires have 1-degree of toe-in.

          8. Set transmitter trims

The steering trim tab on the transmitter should be adjusted

so that the truck rolls straight when you are not touching the

steering wheel/stick. The throttle trim tab should be adjusted

as per the Radio Installation section of the manual.

          9. Check fuel lines

Ensure that all fuel lines are properly connected.